# Fluids: pressure, flow, lift and drag: Viscosity, turbulence and pipe friction: what moving fluid costs

Source page: https://www.materialinsights.org/learn/engineering/fluids/p3/

[All courses](https://www.materialinsights.org/learn/) / [Understanding Engineering](https://www.materialinsights.org/learn/engineering/) / [Module 5: Fluids: pressure, flow, lift and drag](https://www.materialinsights.org/learn/engineering/fluids/) Part 3 of 5

## Viscosity, turbulence and pipe friction: what moving fluid costs

Bernoulli's principle ignores friction, but real fluids stick to walls and drag on each other, and every pipe, duct and channel pays for this in pressure. This part introduces viscosity, the Reynolds number that tells smooth flow from churning flow, the rule for pipe friction, and the way a pump or a fan is sized to cover that cost.

### 3.1 Viscosity is internal friction, and the Reynolds number compares inertia with it

At a sugar mill, molasses creeps out of a tank valve while the wash water beside it gushes. The difference is viscosity, the stickiness with which layers of fluid resist sliding past each other. At the wall of a pipe the fluid sticks, so the layer at the wall is still and the layers further in slide faster. Shearing those layers past each other is a drag that eats energy. Viscosity is measured in pascal seconds. Water at room temperature is about 0.001 Pa s, air about 0.000018, and cool molasses several pascal seconds, thousands of times more than water. Heating usually thins liquids and thickens gases.

Two forces compete in any flow. Inertia is the tendency of moving fluid to carry on, set by density and speed. Viscous force is the tendency of sticky layers to hold each other back. Their ratio is the Reynolds number: Re = density x speed x size / viscosity. Size is a typical length, such as a pipe diameter. It has no units, so it can be compared across a hose, a river and a wing.

A small Re means viscosity wins: the flow is smooth and layered, called laminar. A large Re means inertia wins: small disturbances grow, and the flow becomes a chaotic mix of eddies, called turbulent. In a round pipe, the change happens at a Re of roughly 2,000 to 4,000. The table gives values for everyday cases, and they span about seven orders of magnitude.

Turbulence is not a fault. It mixes quickly, which a heat exchanger or a stirred reactor wants, but it costs more friction, as the next section shows.

Data Worked estimate 6: Reynolds numbers for everyday flows

| Flow | Working: density x speed x size / viscosity | Re | Regime |
|---|---|---|---|
| Molasses in a 25 mm drain pipe at 0.2 m/s (density 1,400 kg/m3, viscosity 5 Pa s, both assumed) | 1,400 x 0.2 x 0.025 / 5 | about 1.4 | laminar, strongly viscous |
| Water in a 15 mm household pipe at 1 m/s | 1,000 x 1 x 0.015 / 0.001 | 15,000 | turbulent |
| Water in the 600 mm city main at 1.5 m/s | 1,000 x 1.5 x 0.6 / 0.001 | 900,000 | fully turbulent |
| Air over a 4.2 m car at 100 km/h (27.8 m/s) | 1.2 x 27.8 x 4.2 / 0.000018 | about 7.8 million | turbulent boundary layer |
| Air over a 0.84 m model of that car at the same speed | same, with 0.84 m | about 1.6 million | turbulent, but smaller (part 5) |

All Re values calculated; units cancel (kg/m3 x m/s x m / Pa s). Check: molasses really does ooze, while the household pipe and city main are well above the 4,000 line, so they churn. Molasses viscosity varies widely with grade and temperature; 5 Pa s is an assumed round figure.
 Source: Bloomfield, How Things Work (Wiley, 2015), ch. 6, 'Fluids and Motion', section 6.1 (viscous forces, laminar and turbulent flows, Reynolds number)  In the data

#### Reynolds numbers you can feel

Smoke from an incense stick rises in a thin laminar thread for the first few centimetres, then breaks into curls as it speeds up and widens and its Reynolds number grows past the point where small wobbles survive. A tap turned to a trickle gives a glassy stream, and turned further it goes cloudy and noisy at the same point. The change from thread to curls is the laminar-to-turbulent transition, visible in a kitchen.

- Bloomfield, How Things Work (Wiley, 2015) · ch. 6, 'Fluids and Motion', section 6.1 (viscous forces, Reynolds number)
- Feynman, Leighton and Sands, The Feynman Lectures on Physics, vol. II (Caltech online edition) · further reading: ch. 41, 'The Flow of Wet Water', https://www.feynmanlectures.caltech.edu/II_41.html

### 3.2 In a long pipe the friction loss grows with the square of the speed, so a small pipe at high flow is costly to pump

Because the fluid sticks to the wall, a long pipe constantly loses pressure. To keep the water moving at a steady speed, a pump must supply pressure equal to the loss. Engineers express this loss as head, the height of water that would give the same pressure. A common form for turbulent flow is the Darcy rule: head loss = f x (length / diameter) x (speed squared / 2g). The symbol f is a friction factor, a pure number that depends on the pipe's roughness and on Re, and for ordinary water pipes is between 0.015 and 0.03.

The rule holds the main lessons of pumping. Loss grows with length: twice the pipe, twice the loss. It grows with the square of speed: twice the flow in the same pipe, four times the loss. It falls with diameter, and since speed itself depends on the diameter through continuity, the combined effect is steep. For a fixed flow rate, loss goes roughly with the inverse fifth power of diameter. Reduce the diameter by one fifth and friction roughly triples.

Pumping power follows from the head. The hydraulic power given to the water is density x g x flow rate x head. The shaft power that the motor must supply is larger by the efficiency of the pump and motor. The table works a typical farm borewell, with the pipe size changed to show its effect.

The trade-off is between pipe cost and the electricity bill. A thin pipe costs little to buy but wastes power every hour for years. Farm pumps run for hundreds of hours a season, so the case for a wider pipe grows with the hours run and with the share of the head that friction takes. This is a choice made on cost over the whole life, a theme that module 13 takes up.

Data Worked estimate 7: a farm borewell pump, 3 litres per second

| Step | Working | Result |
|---|---|---|
| Static lift (assumed) | water 35 m below ground plus 10 m up to a field tank | 45 m |
| Pipe (assumed): bore 50 mm, 60 m long; area | 3.14 x 0.025 x 0.025 | 0.00196 m2 |
| Speed | 0.003 m3/s / 0.00196 m2 | 1.53 m/s |
| Reynolds number | 1,000 x 1.53 x 0.05 / 0.001 | about 76,000, turbulent |
| Friction head (assumed f = 0.025 for an ageing pipe) | 0.025 x (60 m / 0.05 m) x (1.53 x 1.53 m2/s2 / 19.6 m/s2) | 3.6 m |
| Total head | 45 + 3.6 | 48.6 m |
| Hydraulic power | 1,000 kg/m3 x 9.8 m/s2 x 0.003 m3/s x 48.6 m | about 1.43 kW |
| Electrical power at an assumed 40 per cent overall efficiency | 1.43 / 0.4 | about 3.6 kW, close to a 5 horsepower (3.7 kW) motor |
| Same flow in 40 mm pipe | friction head rises to about 10.9 m | total head 55.9 m, power up 15 per cent |
| Same flow in 65 mm pipe | friction head falls to about 1.0 m | total head 46 m, power down 5 per cent |

All results calculated. Check: 5 hp is a common rating of a submersible pump for an Indian farm borewell, and 3 litres per second, about 11 cubic metres an hour, is a typical yield. With friction at about 7 per cent of the total head, the pipe is not the main loss here, but at 40 mm it starts to matter.
 Source: Bloomfield, How Things Work (Wiley, 2015), ch. 6, 'Fluids and Motion', section 6.1 (Poiseuille's law, viscous flow in pipes)  Common misreading

#### 'A bigger pump fixes weak flow'

If a long thin pipe is the problem, a bigger pump pushes more water but at a steeply rising cost. Doubling the flow through the same pipe quadruples the friction head, so the power spent on friction, which is flow x friction head, rises about eightfold. The cheaper cure is often the pipe: one size larger can cut friction several times over. Look at the pipe before you buy the pump.

- Bloomfield, How Things Work (Wiley, 2015) · ch. 6, 'Fluids and Motion', section 6.1 (garden watering, viscous drag in pipes)

### 3.3 A pump gives fluid pressure, and the pipe takes it back: the working point is where the two curves cross

A Centrifugal water pump has a spinning impeller whose vanes fling water outwards. The casing around it slows the fast water and turns its speed into pressure, using Bernoulli's principle in reverse. The motor's shaft power goes into the water as pressure and speed, with losses to friction, leakage and heat. The flow figure follows the energy of the farm pump from the last section.

Every pump has a characteristic: the more flow you ask of it, the less head it can produce. Every pipe system has its own: the more flow you push through it, the more head it needs, a static lift plus friction that grows with speed squared. Plot both and they cross at one point. That is where the pump will actually run. A pump chosen without this check runs far from its best efficiency.

What if you only need half the flow? The common cheap answer is to throttle, closing a valve to add artificial friction. It works and it wastes energy as heat. A better answer is to slow the motor with an electronic drive. Pumps and fans follow affinity rules: flow is proportional to speed, head to speed squared and power to speed cubed. Running at 80 per cent speed gives 80 per cent flow for about half the power (0.8 x 0.8 x 0.8 is 0.51). This cube law is the reason variable-speed drives pay back so quickly on fans and circulating pumps, and it will return in the wind turbine and the Electric motor driving the fan. It holds only where friction makes up most of the head. A borewell pump that must always lift 45 m cannot follow it: slowed by a fifth, it loses most of its head and may deliver little or no water.

Process flowchart Energy chain of the farm borewell pump (estimate 7), per second Inputs **Electricity from the grid**3.6 kW, so 3.6 kJ each second Process steps 1 **Electric motor**

about 85 per cent efficient, loses 0.5 kW as heat in the windings and bearings
 2 **Centrifugal pump**

about 47 per cent hydraulic efficiency, loses about 1.6 kW to churning, leakage and friction in the casing
 3 **Delivery pipe**

friction takes 0.1 kW of the water's pressure
 Outputs **Water lifted 45 m**1.32 kW of useful lifting, about 37 per cent of the electrical input

All results calculated from the estimate: 3.0 kW at the shaft, 1.43 kW delivered to the water, of which friction takes 0.11 kW. Motor 85 per cent and pump 47 per cent are assumed so that the overall efficiency is 40 per cent.
 Source: Bloomfield, How Things Work (Wiley, 2015), ch. 5, 'Fluids', section 5.2 (water distribution and pumps)  In the data

#### The cube law in numbers

Take a 3.7 kW fan, or a pump in a loop where friction is nearly all the head, at full speed. At 90 per cent speed it draws about 2.7 kW, at 80 per cent about 1.9 kW, at 50 per cent about 0.46 kW. Throttled with a valve to the same half flow, it might still draw an assumed 70 per cent of full power, about 2.6 kW. The difference is roughly 2 kW. Over an assumed 2,000 hours a year that is about 4,000 kWh, or Rs 28,000 at an assumed Rs 7 per kWh (all calculated).

- Bloomfield, How Things Work (Wiley, 2015) · ch. 5, 'Fluids', section 5.2 (pressure potential energy, water distribution)

### See it in the table
[H₂O Water](https://www.materialinsights.org/commodities/water/)[Su Sugar](https://www.materialinsights.org/commodities/sugar/)[El Electricity](https://www.materialinsights.org/energy/electricity/)

### Check your understanding

Water at 2 m/s flows in a 50 mm pipe. Which statement about its Reynolds number is right?
 Re = 1,000 x 2 x 0.05 / 0.001 = 100,000, far above the roughly 4,000 line, so the flow is turbulent. Pipe length does not enter the Reynolds number.

A pipe carries a steady flow with a friction head of 4 m. The flow is doubled in the same pipe. What is the new friction head, roughly?
 Turbulent friction head goes with the square of speed, and speed is proportional to flow in a fixed pipe, so doubling flow gives four times the loss.

A pump that follows the affinity rules is slowed to 70 per cent of its speed. About what share of its original power does it draw?
 Power goes as speed cubed: 0.7 x 0.7 x 0.7 = 0.343, about 34 per cent. This is the reason slowing a pump saves far more than throttling it.

[← Part 2: Flow, continuity and Bernoulli: what happens when fluid moves](https://www.materialinsights.org/learn/engineering/fluids/p2/)[Mark read · Part 4: Drag and lift: forces from moving through a fluid →](https://www.materialinsights.org/learn/engineering/fluids/p4/)

## Other sections

- [Module overview](https://www.materialinsights.org/learn/engineering/fluids/index.md)
- [Pressure and buoyancy: what fluids do when they stand still](https://www.materialinsights.org/learn/engineering/fluids/p1/index.md)
- [Flow, continuity and Bernoulli: what happens when fluid moves](https://www.materialinsights.org/learn/engineering/fluids/p2/index.md)
- [Drag and lift: forces from moving through a fluid](https://www.materialinsights.org/learn/engineering/fluids/p4/index.md)
- [Fans, propellers, turbines and models: putting flow to work and learning to predict it](https://www.materialinsights.org/learn/engineering/fluids/p5/index.md)
- [Key terms, quiz and sources](https://www.materialinsights.org/learn/engineering/fluids/review/index.md)
