# Thinking in estimates: units, scaling and educated guessing: Scaling: why size changes everything

Source page: https://www.materialinsights.org/learn/engineering/thinking-in-estimates/p4/

[All courses](https://www.materialinsights.org/learn/) / [Understanding Engineering](https://www.materialinsights.org/learn/engineering/) / [Module 2: Thinking in estimates: units, scaling and educated guessing](https://www.materialinsights.org/learn/engineering/thinking-in-estimates/) Part 4 of 5

## Scaling: why size changes everything

Make a thing twice as big in every direction and it does not behave twice as strongly, twice as hot or twice as heavy. Different properties grow at different rates, and that mismatch explains why a bridge cannot be a scaled-up model, why a large motor needs a fan and a small one does not, and why big tanks keep heat better. This part gives the arithmetic of size.

### 4.1 Area grows as length squared and volume as length cubed

Take a cube of side 1 cm. Its surface is six faces of 1 cm2, so 6 cm2, and its volume is 1 cm3. Now double every edge. The faces become 2 cm by 2 cm, so each has four times the area, and the whole surface is 24 cm2. The volume becomes 2 x 2 x 2, which is 8 cm3. Doubling the length quadruples the area and multiplies the volume by eight. This holds for any shape, as long as the shape itself does not change.

In general, if you scale all lengths by a factor k, areas scale by k squared and volumes by k cubed. Surface per unit volume therefore falls as one over k. Almost every physical effect depends on one or the other. Weight, thermal mass, the heat a machine generates inside itself and the amount of material needed are tied to volume. Heat lost through a surface, the cooling of a hot body, drying, evaporation and the strength of a rope or column, which depends on its cross-section, are tied to area.

You have seen the effect. A cup of chai goes cold in minutes, while a 20-litre milk can stays hot for hours, and crushed ice melts faster than a block of equal weight.

The table lists the ratios you need most.

A rule of the form 'proportional to length to the power n' is called a scaling law. Spotting which power applies is most of the work.

Data What happens when all lengths are scaled up

| Quantity | Scales as | Length x 2 | Length x 10 |
|---|---|---|---|
| Length | L | 2 | 10 |
| Surface area, cross-section, strength of a column | L2 | 4 | 100 |
| Volume, mass, weight, heat produced inside | L3 | 8 | 1,000 |
| Stress caused by own weight (weight / cross-section) | L | 2 | 10 |
| Surface per unit volume | 1 / L | 1/2 | 1/10 |
| Heat lost through the surface at a fixed temperature difference | L2 | 4 | 100 |

Valid when the shape is kept the same and the material is unchanged.
 Source: Mahajan, Street-Fighting Mathematics (MIT Press, 2010), ch. 1, 'Dimensions' (reasoning with lengths, areas and volumes); table compiled for this course  Worked example

#### Why a scale model of a bridge flatters the real one

Build a model of a bridge one fiftieth of the size from the same material. The model's weight falls by a factor of 50 cubed, but its cross-sections fall only by 50 squared, so the stress from its own weight is 50 times smaller than in the real bridge. The model carries its own weight with ease and can even carry a heavy load. The real structure, with the same shape and material, is under 50 times the stress. Models are useful for many things, but a model that does not fail proves little about the full size.

- Mahajan, Street-Fighting Mathematics (MIT Press, 2010) · ch. 1, 'Dimensions' and ch. 2, 'Easy cases' (reasoning with lengths, areas and volumes)

### 4.2 Strength grows more slowly than weight, so every structure has a largest size

Take the simplest tall structure, a straight column of uniform thickness standing on the ground. The weight of the column is density x gravity x cross-section area x height. The base must carry all of it, spread over the cross-section. Divide one by the other and the area cancels: the stress at the base is density x gravity x height. Making the column thicker does not help at all. Only a stronger material, a lower height or a base wider than the top will.

Set this stress equal to the strength of the material and you have the greatest height the column could reach before crushing under itself. Concrete of grade M30, common in Indian building, has a characteristic compressive strength of 30 N/mm2, or 30 million pascals. Reinforced concrete weighs about 2,500 kg per cubic metre. The limit is 30 x 10^6 / (2,500 x 9.8), about 1,200 m. Nobody designs to the breaking point, so apply a safety factor, as module 1 explained. With 3, assumed here, the working height is about 400 m.

Now the check. The tallest building in the world, the Burj Khalifa, is 828 m high, roughly twice the safe height for a uniform M30 column. There is no contradiction. Its footprint shrinks as it rises, its walls use concrete of cube strength 60 to 80 N/mm2, and its top 200 m or more is a steel spire. At 80 N/mm2 a uniform column with the same margin could reach about 1,100 m (calculated), so for the strongest concrete, wind and the floors carried matter as much as self-weight. Still, a few hundred metres is where ordinary concrete needs special measures: see 'Steel-frame skyscraper' and 'Reinforced concrete' on the site, and 'Prestressed concrete', where steel tendons keep concrete squeezed so that it resists bending.

The lesson reaches beyond buildings. Doubling a design in every direction doubles the stress from its own weight, so large structures must change shape, material or both.

Data Worked estimate: how tall can a uniform concrete column stand under its own weight?

| Step | Working | Result |
|---|---|---|
| Stress at the base | weight / area = (density x area x height x g) / area | density x g x height; area cancels |
| Strength of the material | Grade M30: characteristic compressive strength 30 N/mm2 | 30 x 10^6 Pa |
| Height at crushing | 30 x 10^6 / (2,500 kg/m3 x 9.8 m/s2) | about 1,200 m |
| With a margin of 3 (assumed) | 1,200 / 3 | about 400 m |
| Check against a real value | Burj Khalifa, 828 m; walls of C60 to C80 concrete, a steel spire of over 200 m, footprint shrinking with height | About twice the M30 answer; at 80 N/mm2 a uniform column with the same margin could reach about 1,100 m (calculated) |

The strength is the grade designation used in Indian codes; the 2,500 kg/m3 density is the module 1 figure for reinforced concrete (IS 456 takes 25 kN/m3, about 2,550 kg/m3). Tower design involves wind and many other loads not considered here.
 Source: Council on Tall Buildings and Urban Habitat, Skyscraper Center entry for Burj Khalifa, architectural height 828 m, completed 2010, steel over concrete, https://www.skyscrapercenter.com/building/burj-khalifa/3  Common misreading

#### 'A thicker column can stand taller'

Thickness cancels out of the self-weight stress, because a fatter column is heavier in exact proportion to the area carrying it. A thick column can carry a bigger load placed on top, but it cannot support more of its own height. This is why tall towers and chimneys narrow upward.

- Mahajan, Street-Fighting Mathematics (MIT Press, 2010) · ch. 1, 'Dimensions' (using ratios and powers of length)
- Council on Tall Buildings and Urban Habitat, Skyscraper Center entry for Burj Khalifa · architectural height 828 m, completed 2010, steel over concrete, https://www.skyscrapercenter.com/building/burj-khalifa/3
- Bureau of Indian Standards, IS 456:2000 Plain and Reinforced Concrete: Code of Practice · grades of concrete designated by characteristic compressive strength in N/mm2 (M30 means 30); unit weight of reinforced concrete 25 kN/m3
- Novak, 'A tall adventure: the Burj Khalifa, the world's tallest structure', Building Safety Journal (International Code Council, 8 August 2023) · wall concrete C60 to C80 cube strength; telescopic structural steel spire of over 200 m, https://www.iccsafe.org/building-safety-journal/bsj-technical/a-tall-adventure-the-burj-khalifa-the-worlds-tallest-structure/

### 4.3 Heat is lost through the surface and made in the volume, so big and small machines differ

Put the two laws side by side. Heat that leaks out of a hot tank goes through its surface, which grows as the square of the size. The water that holds the heat grows as the cube. A larger tank loses a smaller share of its heat each day. Heat made inside a machine, in the windings of a motor or the core of a transformer, grows with the volume of the working material, yet it has to leave through the surface. A larger machine therefore runs hotter unless its cooling is improved.

Take a storage water heater. A 25-litre geyser is a cylinder about 0.25 m across and 0.5 m tall. Its surface is roughly 0.49 m2. With a 30 mm layer of polyurethane foam, whose conductivity is about 0.025 W per metre per kelvin (an assumed typical value), heat passes at about 0.83 W per m2 for each kelvin of temperature difference. At 45 K above the room this is 0.83 x 0.49 x 45, about 18 W, which is 0.44 kWh a day. Now double every dimension. The tank holds 8 times as much, 200 litres, but its surface is 4 times larger, so the same foam loses 73 W, or 1.76 kWh a day.

Check against the national energy label. Under the star table for 2023 to 2025, the best-rated 25-litre heater could lose at most 0.465 kWh a day under the test conditions, so our estimate is within about 5 per cent. The best-rated 200-litre heater could lose at most 0.984 kWh a day, and our estimate for the larger tank is nearly double. The miss is informative: to meet the label, the maker needs about 55 mm of foam, nearly twice as thick, and a tighter table reported from July 2026 lowers both limits by about a tenth. Scaling gave the direction; the label shows the designer's extra work.

The same reasoning explains fins, fans and oil circuits on large machines.

Data Worked estimate: heat leak of a storage water heater, small and large

| Step | Working | Result |
|---|---|---|
| Small tank (25 L) | Cylinder 0.25 m across, 0.5 m tall: volume about 0.0245 m3 | about 25 litres |
| Surface area | Side: 3.14 x 0.25 x 0.5 = 0.39 m2; two ends: 2 x 3.14 x 0.125 squared = 0.10 m2 | 0.49 m2 |
| Heat leak, 30 mm foam, 45 K | (0.025 / 0.03) x 0.49 x 45 | 18 W, or 0.44 kWh in 24 hours |
| Double every size | Surface x 4 = 1.96 m2; volume x 8 = 196 litres | about 200 litres |
| Same foam on the large tank | 0.83 x 1.96 x 45 | 73 W, or 1.76 kWh in 24 hours |
| Check, small tank | BEE 5-star limit for 25 L, 2023 to 2025 table: 0.465 kWh in 24 hours | Estimate within about 5 per cent |
| Check, large tank | BEE 5-star limit for 200 L, 2023 to 2025 table: 0.984 kWh in 24 hours | Needs about 30 x 1.76 / 0.984 = 54 mm of foam, say 55 |

The label's limits are standing losses scaled to a 45 K difference between water and surroundings: the Indian test standard, IS 2082, measures the loss at its own water and room temperatures and multiplies it by 45 divided by the measured difference. A table reported for 1 July 2026 to 31 December 2027 sets the 5-star limits at 0.423 kWh (25 L) and 0.890 kWh (200 L). Foam conductivity is an assumed typical value. Results are calculated.
 Source: Bureau of Energy Efficiency, note on star labelling of storage water heaters (star rating plan valid 1 January 2023 to 31 December 2025), Table 3.4 standing loss limits in kWh per 24 hours per 45 degrees C, https://beeindia.gov.in/sites/default/files/GeyserNote.pdf  Case

#### Why large transformers grow radiators

Losses in a transformer arise through its whole core and windings, so they rise with volume. The surface that sheds them rises only with area. Double the size and, with unchanged materials, the heat goes up eightfold while the cooling surface goes up fourfold, so the temperature rise doubles. Small distribution transformers manage with ribbed tanks. Big power transformers carry banks of radiators, oil pumps and fans. The 'Transformer and power converter' product shows the same logic at many sizes: the bigger the unit, the larger the share of its design that is cooling.

- Bureau of Energy Efficiency, note on star labelling of storage water heaters (star rating plan valid 1 January 2023 to 31 December 2025) · Table 3.4 standing loss limits in kWh per 24 hours per 45 degrees C, https://beeindia.gov.in/sites/default/files/GeyserNote.pdf
- Bureau of Indian Standards, IS 2082:1993 Stationary Storage Type Electric Water Heaters: Specification · clause 16.1, standing loss per 24 hours scaled to a 45 K difference between mean water temperature and ambient, https://law.resource.org/pub/in/bis/S05/is.2082.1993.pdf
- VSC Times, 'BEE star ratings for water heaters (geysers)' (2026, secondary report of the BEE table) · 5-star limits 0.423 kWh (25 L) and 0.890 kWh (200 L) per 24 hours per 45 degrees C, table valid 1 July 2026 to 31 December 2027, https://vsctimes.com/bee-star-ratings-for-water-heaters-geysers/
- Mahajan, Street-Fighting Mathematics (MIT Press, 2010) · ch. 3, 'Lumping' (treating a real object as a simple shape of the right size)

### See it in the table
[H₂O Water](https://www.materialinsights.org/commodities/water/)[St Steel](https://www.materialinsights.org/commodities/steel/)

### Check your understanding

A tank is rebuilt with every dimension three times larger and the same insulation. How does its heat loss change, and how does its water volume change?
 Heat loss follows surface area, which grows as the square of the scale factor, giving 9. Volume follows the cube, giving 27. The loss per litre therefore falls to one third.

Why does making a concrete column thicker not allow it to stand taller under its own weight?
 Stress at the base equals density x g x height, and the cross-section area cancels.

A large motor and a small motor of the same design both run at the same internal heating per unit volume. Which statement is correct?
 Heat produced grows with volume while cooling grows with surface area, so the larger machine has less surface for each unit of heat.

[← Part 3: The big part first, then rounding, lumping and pictures](https://www.materialinsights.org/learn/engineering/thinking-in-estimates/p3/)[Mark read · Part 5: When an estimate is good enough to decide →](https://www.materialinsights.org/learn/engineering/thinking-in-estimates/p5/)

## Other sections

- [Module overview](https://www.materialinsights.org/learn/engineering/thinking-in-estimates/index.md)
- [Why engineers estimate before they calculate](https://www.materialinsights.org/learn/engineering/thinking-in-estimates/p1/index.md)
- [Dimensions and easy cases: checking formulas and finding them](https://www.materialinsights.org/learn/engineering/thinking-in-estimates/p2/index.md)
- [The big part first, then rounding, lumping and pictures](https://www.materialinsights.org/learn/engineering/thinking-in-estimates/p3/index.md)
- [When an estimate is good enough to decide](https://www.materialinsights.org/learn/engineering/thinking-in-estimates/p5/index.md)
- [Key terms, quiz and sources](https://www.materialinsights.org/learn/engineering/thinking-in-estimates/review/index.md)
