# Heat, temperature and the laws of thermodynamics: How heat moves: conduction, convection and radiation

Source page: https://www.materialinsights.org/learn/science/heat-and-temperature/p5/

[All courses](https://www.materialinsights.org/learn/) / [Understanding Science](https://www.materialinsights.org/learn/science/) / [Module 5: Heat, temperature and the laws of thermodynamics](https://www.materialinsights.org/learn/science/heat-and-temperature/) Part 5 of 6

## How heat moves: conduction, convection and radiation

Heat has three ways to travel. It can pass along a solid from particle to particle, ride on the flow of a fluid, or cross empty space as light. Each has its own rule, and together they decide why a steel spoon burns the fingers, why a heater belongs low in a room, why Earth is habitable and how stars are measured from far away.

### 5.1 Conduction passes energy from particle to particle, and trapped air is the best insulator

Pour hot chai into a steel tumbler and into a clay kulhad. The steel soon burns the fingers while the kulhad can be held. Steel passes heat through its thin wall almost at once; baked clay passes it slowly, so its outer face stays cooler. Your skin reports that rate, not the tea's temperature.

Conduction is heat passing through matter without the matter moving. At the hot end the particles jiggle hard. They knock their neighbours, who knock theirs, and energy diffuses along. In metals there is a second route: loose electrons that carry energy quickly through the whole piece. That is why metals that conduct electricity well, copper and aluminium, also conduct heat well.

The rate follows Fourier's rule: heat per second = k x A x (temperature difference) / thickness. Here A is the area, and k is the thermal conductivity, a number for each material. The Heat conduction (Fourier's law) node tells how Fourier found it in 1822. Metals are the best conductors: copper has a k near 390 W/m K, carbon steel about 43, glass about 1 and water about 0.6 (Engineering ToolBox). Doubling the thickness halves the flow, and doubling the area doubles it. Stacked layers add their resistances, thickness / k, as resistors in series do. The table applies the rule to a cool box.

Gases are the poorest conductors because molecules are far apart. Still air has a k of about 0.026 W/m K, about five times lower than softwood and some 15,000 times lower than copper. This is the key to insulation. Wool, foam, double-glazed windows and thermocol all work by holding pockets of air too small to circulate.

Data Worked estimate: how long does ice last in a thermocol box? (outside 35 °C, inside 0 °C)

| Step | Working | Result |
|---|---|---|
| Box 40 x 30 x 30 cm: area of all six faces | 2 x (0.4 x 0.3 + 0.4 x 0.3 + 0.3 x 0.3) m² | 0.66 m² (calculated) |
| Resistance of a 25 mm wall of expanded polystyrene, k = 0.03 W/m K | 0.025 m / 0.03 W/m K | 0.83 m² K/W (calculated) |
| Heat leaking in | 0.66 m² x 35 K / 0.83 m² K/W | about 28 W (calculated) |
| Energy to melt 5 kg of ice (latent heat 334 kJ/kg) | 5 kg x 334,000 J/kg | 1.67 MJ (calculated) |
| Time until the ice is gone | 1.67e6 J / 28 W = 60,000 s | about 17 hours (calculated) |
| Same box with 50 mm walls | resistance doubles, so the leak halves to about 14 W | about 33 hours (calculated) |

Calculated with Engineering ToolBox conductivities in W per metre per kelvin: copper about 390, aluminium 236, carbon steel 43, glass 1.05, water 0.61, common brick 0.6 to 1.0, softwood 0.12, air 0.026, expanded polystyrene 0.03. Thin films of still air on each face add a little resistance and the corners leak a little more, so a real box lasts roughly this long.
 Source: Engineering ToolBox, Thermal conductivity of common materials, and of metals and alloys, https://engineeringtoolbox.com/thermal-conductivity-d_429.html and https://engineeringtoolbox.com/thermal-conductivity-metals-d_858.html (W/m K: air 0.0262 at 25 C; expanded polystyrene 0.03; glass 1.05; water 0.606; common brick 0.6 to 1.0; softwood 0.12; electrolytic copper 390; aluminium 236; 1% carbon steel 43; type 304 stainless 14.4)  Common misreading

#### Insulators do not make heat

Wrap a block of ice in a thick woollen blanket and it melts more slowly than a bare one, not faster. A blanket gives no warmth; it slows the escape of the warmth you make. Insulation reduces the rate of heat transfer in either direction. It creates or destroys none of it, and only changes how fast temperatures even out.

- Hewitt, Lyons, Suchocki and Yeh, Conceptual Integrated Science, 2nd edition (Pearson, 2013) · ch. 6, 'Heat'
- [Engineering ToolBox, Thermal conductivity of common materials, and of metals and alloys](https://engineeringtoolbox.com/thermal-conductivity-d_429.html and https://engineeringtoolbox.com/thermal-conductivity-metals-d_858.html (W/m K: air 0.0262 at 25 C; expanded polystyrene 0.03; glass 1.05; water 0.606; common brick 0.6 to 1.0; softwood 0.12; electrolytic copper 390; aluminium 236; 1% carbon steel 43; type 304 stainless 14.4)) · web
- Feynman, Leighton and Sands, The Feynman Lectures on Physics, Vol. I (Caltech) · further reading only: https://www.feynmanlectures.caltech.edu/I_39.html (the kinetic theory of gases), I_44 (the laws of thermodynamics), I_45 (illustrations of thermodynamics) and I_46 (ratchet and pawl)

### 5.2 Convection carries heat by the flow of a fluid, because warmed fluid expands and rises

Put a pan of water on the flame with a few tea leaves in it: they ride up the middle and drift down the sides. The layer touching the hot base warms, swells a little and becomes lighter for its size than the water above. Buoyancy (see the Buoyancy (Archimedes' principle) node) lifts it, and the cooler water above sinks to the base to be heated in turn. The loop carries heat through the pan far faster than conduction could. This is convection: heat moved by the bulk movement of a fluid.

Convection needs gravity. In an orbiting spacecraft, in free fall, warm air does not rise and a candle flame forms a dim ball that dies for want of fresh air (see 'Gravity, projectiles and orbits' on weightlessness).

The scale runs from a kettle to the planet. A room heater near the floor warms the room because the warm air it makes rises and the cool air sinks to be heated in turn, while a heater near the ceiling leaves the floor cold. An air conditioner is put high for the opposite reason: cooled air is denser and falls. Winds are convection currents of the atmosphere. Sea breezes, and the monsoon of the previous part, are convection with the sea as the cold side. Ocean currents move heat from the tropics to the poles. Even the Earth's solid mantle creeps in slow cells (see the Plate tectonics node).

Fans and pumps add forced convection, moving air or water faster than buoyancy alone, as in a laptop or a car radiator.

Data Worked estimate: how much can the hot air in a balloon lift?

| Step | Working | Result |
|---|---|---|
| Density of air at 30 °C (303 K) | 101,325 Pa / (287 J per kg per K x 303 K) | 1.165 kg/m³ (calculated) |
| Density of air at 100 °C (373 K) | 101,325 / (287 x 373) | 0.947 kg/m³ (calculated) |
| Difference per cubic metre | 1.165 - 0.947 | 0.22 kg/m³ (calculated) |
| Lift of a 2,800 m³ passenger balloon | 0.22 kg/m³ x 2,800 m³ | about 610 kg (calculated) |
| What it must carry | envelope, basket, burners, fuel and people | roughly this much |

Calculated from the ideal gas law with air at constant pressure; density is proportional to 1 / T. A typical passenger balloon holds about 2,800 m³.
 Common misreading

#### 'Heat rises' is not quite right

Heat spreads in every direction by conduction and radiation. What rises is warm air, because of its lower density. A hot object also warms things beside it and below it. In a fluid with no gravity warm parts do not rise at all. The correct statement is that warmed fluids expand and are pushed upward by the cooler fluid around them.

- Hewitt, Lyons, Suchocki and Yeh, Conceptual Integrated Science, 2nd edition (Pearson, 2013) · ch. 6, 'Heat'
- Feynman, Leighton and Sands, The Feynman Lectures on Physics, Vol. I (Caltech) · further reading only: https://www.feynmanlectures.caltech.edu/I_39.html (the kinetic theory of gases), I_44 (the laws of thermodynamics), I_45 (illustrations of thermodynamics) and I_46 (ratchet and pawl)

### 5.3 Radiation carries heat across empty space, and every warm body glows at a colour set by its temperature

The Sun's heat reaches us across 150 million km of vacuum. No fluid carries it and no solid conducts it. It comes as electromagnetic waves, the family that includes light and radio. Every object above absolute zero gives out such radiation, because its jiggling charges shake the electromagnetic field.

In 1800 William Herschel moved a thermometer along the Sun's spectrum cast by a prism. It warmed most beyond the red end, where nothing could be seen. He had found infrared. Josef Stefan measured in 1879, and Ludwig Boltzmann derived in 1884, that the power radiated by a surface goes as the fourth power of its kelvin temperature: P = e x s x A x T^4, with s = 5.67e-8 W/m² K^4 and e between 0 and 1. Wien (1893) found that the peak wavelength is inversely proportional to T: peak wavelength = 2.898e-3 m K / T. Planck explained both in 1900 (see the Blackbody radiation node).

So a colour gives a temperature. A body at 5,770 K peaks near 500 nm, in the green of visible light. Your skin, at about 307 K, peaks near 9.4 micrometres, in the infrared. A 2,700 K bulb filament peaks near 1.1 micrometres, so most of its output is infrared.

Gustav Kirchhoff showed in 1859 that, wavelength by wavelength, a surface absorbs and emits equally well. Otherwise a dark object in a closed room would end up warmer than a pale one beside it. So soot both soaks up and gives out radiation readily, and polished metal does neither. Lime-washed roofs use the wavelength rule: they reflect most sunlight but radiate infrared almost as well as a black body, so they stay cool. A surface warms when it absorbs more than it emits, and cools when it emits more. On a clear night the ground radiates to the cold sky and gets little back, so it cools and dew or frost forms. Cloud sends radiation back, so cloudy nights are warmer.

Data Peak wavelength of thermal radiation (Wien's rule, calculated)

| Source | Temperature (K) | Peak wavelength | Region |
|---|---|---|---|
| Surface of the Sun | 5,770 | about 0.50 micrometres (calculated) | visible |
| Incandescent bulb filament | 2,700 | about 1.1 micrometres (calculated) | near infrared |
| Human skin | 307 | about 9.4 micrometres (calculated) | infrared |
| Earth's surface | 288 | about 10 micrometres (calculated) | infrared |
| Cosmic microwave background | 2.725 | about 1.06 mm (calculated) | microwave |

Calculated from peak wavelength = 2.898e-3 m K divided by the temperature. The microwave background temperature is from NASA's COBE measurement. A bare person of 1.5 m² at skin temperature 307 K in a 293 K room loses about 0.97 x 5.67e-8 W/m² K^4 x 1.5 m² x (307^4 - 293^4) K^4 = about 125 W by radiation alone (calculated), with a skin emissivity of 0.97.
 Source: NASA NSSDCA, Earth Fact Sheet, https://nssdc.gsfc.nasa.gov/planetary/factsheet/earthfact.html (solar irradiance 1361.0 W/m2; black-body temperature 254.0 K; mean temperature 288 K; Bond albedo 0.294); NASA LAMBDA, COBE FIRAS overview, https://lambda.gsfc.nasa.gov/product/cobe/firas_overview.html (cosmic microwave background is a near-perfect blackbody at 2.725 +/- 0.002 K)  In the data

#### Why the Earth is 33 K warmer than a simple sum says

Sunlight at the top of the atmosphere carries 1361 W/m² (NASA). The Earth reflects 29.4 per cent, and the disc that catches the light is a quarter of the sphere's surface area, so the average absorbed is 1361 x (1 - 0.294) / 4 = about 240 W/m² (calculated). A black surface giving out 240 W/m² would be at (240 / 5.67e-8)^0.25 = 255 K (calculated), matching NASA's 254 K. The actual mean surface temperature is 288 K. The 33 K difference is the greenhouse effect: air that passes sunlight but absorbs outgoing infrared (see the Greenhouse effect node).

- Hewitt, Lyons, Suchocki and Yeh, Conceptual Integrated Science, 2nd edition (Pearson, 2013) · ch. 6, 'Heat'
- [NASA NSSDCA, Earth Fact Sheet](https://nssdc.gsfc.nasa.gov/planetary/factsheet/earthfact.html (solar irradiance 1361.0 W/m2; black-body temperature 254.0 K; mean temperature 288 K; Bond albedo 0.294)) · web
- [NASA LAMBDA, COBE FIRAS overview](https://lambda.gsfc.nasa.gov/product/cobe/firas_overview.html (cosmic microwave background is a near-perfect blackbody at 2.725 +/- 0.002 K)) · web
- Feynman, Leighton and Sands, The Feynman Lectures on Physics, Vol. I (Caltech) · further reading only: https://www.feynmanlectures.caltech.edu/I_39.html (the kinetic theory of gases), I_44 (the laws of thermodynamics), I_45 (illustrations of thermodynamics) and I_46 (ratchet and pawl)

### See it in the table
[H₂O Water](https://www.materialinsights.org/commodities/water/)[Cu Copper](https://www.materialinsights.org/commodities/copper/)[Al Aluminium](https://www.materialinsights.org/commodities/aluminum/)[St Steel](https://www.materialinsights.org/commodities/steel/)[CaO Lime](https://www.materialinsights.org/commodities/lime/)[Tea Tea](https://www.materialinsights.org/commodities/tea/)[Wl Wool](https://www.materialinsights.org/commodities/wool/)[Oc Ocean currents](https://www.materialinsights.org/energy/e_currents/)[El Electricity](https://www.materialinsights.org/energy/electricity/)

### Check your understanding

Why does a thick woollen blanket keep a block of ice from melting quickly?
 Insulators work by slowing heat transfer. Still air is a poor conductor and the fibres stop it circulating, so the blanket slows heat entering as well as leaving.

A wall's resistance (thickness / k) doubles. What happens to the heat passing through for the same temperature difference?
 Heat flow per square metre = temperature difference / resistance, so doubling resistance halves the flow.

A star glows blue-white and another glows red. Which is hotter, and why?
 By Wien's rule the peak wavelength is inversely proportional to temperature. A hotter surface peaks at shorter wavelengths, towards blue.

[← Part 4: Expansion: bridges, rails, ice and the strange case of water](https://www.materialinsights.org/learn/science/heat-and-temperature/p4/)[Mark read · Part 6: The second law, entropy and why heat flows one way →](https://www.materialinsights.org/learn/science/heat-and-temperature/p6/)

## Other sections

- [Module overview](https://www.materialinsights.org/learn/science/heat-and-temperature/index.md)
- [Temperature is the average motion of molecules](https://www.materialinsights.org/learn/science/heat-and-temperature/p1/index.md)
- [Heat is energy in transit, and how experiment showed it](https://www.materialinsights.org/learn/science/heat-and-temperature/p2/index.md)
- [Specific heat: why water, sand and steel warm at different rates](https://www.materialinsights.org/learn/science/heat-and-temperature/p3/index.md)
- [Expansion: bridges, rails, ice and the strange case of water](https://www.materialinsights.org/learn/science/heat-and-temperature/p4/index.md)
- [The second law, entropy and why heat flows one way](https://www.materialinsights.org/learn/science/heat-and-temperature/p6/index.md)
- [Key terms, quiz and sources](https://www.materialinsights.org/learn/science/heat-and-temperature/review/index.md)
