# Gas turbine: Working

Source page: https://www.materialinsights.org/products/p_gas_turbine/prod-working/

#### What it is

The product and the job it does, in a short paragraph

A gas turbine is an engine in which compressed air and fuel burn continuously and the hot gas spins a turbine. This node covers the larger gas turbines of the trade heading for turbines above a set power that drive generators, compressors and pumps in power plants and industry: large heavy-duty frame machines and smaller aeroderivative units built from aircraft engine designs. The functional unit is one gas turbine, the turbine unit alone. Generators, steam turbines, heat recovery boilers and foundations are left out, as are aircraft and military engines.

as of 2026-11-13

#### How it works

How it does its job, step by step in plain words

Air enters at the front and a compressor squeezes it to many times atmospheric pressure. In the combustor fuel, usually natural gas, burns in that air at steady pressure, and the gas leaves very hot. The hot gas expands through turbine stages and spins their blades. A large part of that work drives the compressor on the same shaft; the rest turns a generator, compressor or pump. The exhaust is still hot, so in a combined cycle it raises steam for a steam turbine: GE quotes over 64% for its largest units in combined cycle against 44.0% for the turbine alone ^[4]. The first blades meet gas hotter than their alloy can bear, so they are coated with ceramic and cooled by air ^[7].

as of 2026-11-13

#### Key specifications

The numbers that describe it, each with unit, variant, year and source

| Spec | Value | Unit | Variant | Year | Source |
|---|---|---|---|---|---|
| Simple-cycle net output, GE 9HA.02 (50 Hz) | 571 | MW | Heavy-duty | – | ^[4] |
| Net efficiency (lower heating value), GE 9HA.02 (50 Hz), simple cycle | 44 | % | Heavy-duty | – | ^[4] |
| Simple-cycle net output, GE 9HA.01 (50 Hz) | 448 | MW | Heavy-duty | – | ^[4] |
| Combined-cycle efficiency given by GE on its 9HA page (not tied to one model) | 64 | % (more than) | Heavy-duty | – | ^[4] |
| Net output, GE LMS100 PA+ (50 Hz) | 112.9 | MW | Aeroderivative | – | ^[5] |
| Net efficiency (lower heating value), GE LMS100 PA+ | 43 | % | Aeroderivative | – | ^[5] |
| Dry mass of the 16 MW GTU-16P studied in one life cycle assessment (one unit, made in Russia) | 5150 | kg | Aeroderivative | 2024 | ^[2]^[3] |
| Shaft power of the GTU-16P | 16 | MW | Aeroderivative | 2024 | ^[2]^[3] |
| Full resource of the GTU-16P installation; the preprint gives overhauls after 25,000 h (gas generator) and 50,000 h (power turbine) | 100,000 | hours | Aeroderivative | 2024 | ^[2]^[3] |

as of 2026-11-13. GE figures are from undated product pages (50 Hz tables). The GTU-16P rows describe one unit in one study; the paper says it is built on the gas generator of an aircraft engine, which makes it an aeroderivative [2][3].

#### Variants

The variants whose make-up or footprint differs a lot, what defines each and its share of units

| Variant | Defining spec | Year | Source |
|---|---|---|---|
| Heavy-duty | Large frame turbines, such as the 448 to 571 MW GE 9HA, for combined-cycle and peaking plants. Advanced-frame units above 225 MW were about 80% of 2024 orders by MW ^[13] | 2024 | ^[4]^[13]; no unit shares by variant found |
| Aeroderivative | Smaller, lighter units built on aircraft engine designs, such as the 113 MW GE LMS100, for peaking, on-site power and mechanical drive ^[5]; the 16 MW GTU-16P of the bill of materials is one ^[2] | 2024 | ^[5]^[2]; no unit shares by variant found |

as of 2026-11-13

#### Limits

The physical limits set by science and the engineering limits of today's design, with today's value

| Limit | Kind | Limit | Today | Unit | Source |
|---|---|---|---|---|---|
| No heat engine can exceed the Carnot limit set by its hottest and coldest temperatures; no limit value was found for gas turbines, so only the best measured plant is shown | Physical | – | 63.08 | % gross efficiency (best combined-cycle plant, not a limit) | ^[6] |
| Gas temperature at the turbine inlet against the melting point of the blade alloy: nickel superalloys melt at about 1250 degrees C, yet an F-class Mitsubishi turbine described in a 2021 review runs at a 1350 degrees C inlet temperature, so cooling air and ceramic coatings bridge the gap | Engineering | 1250 | 1350 | degrees C | ^[7] |
| Largest simple-cycle output among the GE product pages opened (not a limit) | Engineering | – | 571 | MW | ^[4] |

as of 2026-11-13

#### Science it relies on

The science principles it works by or is limited by
 Relies on

- [Combustion chemistry](https://www.materialinsights.org/science/combustion_chemistry/) Burning fuel in compressed air releases the heat that the turbine turns into work.
- [First law of thermodynamics](https://www.materialinsights.org/science/first_law_thermodynamics/) Heat added in the combustor is converted into shaft work plus exhaust heat.
 Limited by

- [Carnot's limit on heat engines](https://www.materialinsights.org/science/carnot_cycle/) Efficiency is capped by the gap between combustor and exhaust temperatures, which is why makers push the temperature up.

as of 2026-11-13

#### Sources

1. [Life cycle assessment of a gas turbine installation in the Russian Federation (Global Energy 30(2), 74-87; in Russian)](https://engtech.spbstu.ru/userfiles/files/articles/2024/2/Mozzhegorova%2C-Ilinih%2C-Korotaev.pdf) Peter the Great St Petersburg Polytechnic University, 2024
2. [Life Cycle Assessment of a Gas Turbine Installation (preprint, version 1, 24 November 2023)](https://www.preprints.org/manuscript/202311.1582) Preprints.org, 2023
3. [9HA Gas Turbine: 9HA.01 and 9HA.02 (product page)](https://www.gevernova.com/gas-power/products/gas-turbines/9ha) GE Vernova
4. [LMS100 Aeroderivative Gas Turbine (product page)](https://www.gevernova.com/gas-power/products/gas-turbines/lms100) GE Vernova
5. [GE HA Turbine Snags Another World Record for CCGT Efficiency](https://www.powermag.com/ge-ha-turbine-snags-another-world-record-for-ccgt-efficiency) POWER Magazine, 2018
6. [Test-Rig Simulation on Hybrid Thermal Barrier Coating Assisted with Cooling Air System for Advanced Gas Turbine under Prolonged Exposures: A Review](https://mdpi.com/2079-6412/11/5/560) MDPI, Coatings 11(5), 560, 2021
7. [Gas Turbine Market Report: 2024 Posts Highest Units, MWs in 22 Years](https://www.turbomachinerymag.com/view/gas-turbine-market-report-2024-posts-highest-units-mws-in-22-years) Turbomachinery International, 2025

## Other sections

- [Summary](https://www.materialinsights.org/products/p_gas_turbine/index.md)
- [Bill of materials](https://www.materialinsights.org/products/p_gas_turbine/prod-bom/index.md)
- [Use case](https://www.materialinsights.org/products/p_gas_turbine/prod-use/index.md)
- [Supply chain](https://www.materialinsights.org/products/p_gas_turbine/prod-supply/index.md)
- [Footprint](https://www.materialinsights.org/products/p_gas_turbine/prod-footprint/index.md)
- [Evolution](https://www.materialinsights.org/products/p_gas_turbine/prod-evolution/index.md)
- [Interventions](https://www.materialinsights.org/products/p_gas_turbine/prod-interventions/index.md)
