# Machine tool: Footprint

Source page: https://www.materialinsights.org/products/p_machine_tool/prod-footprint/

#### Raw materials in one unit

Every commodity and chemical inside one unit, traced through its components by the site, with its emission factor and emissions

| Variant | Material | Amount (kg) | Through | Emission factor (kg CO2e per kg) | Emissions (kg CO2e) |
|---|---|---|---|---|---|
| Machining | Steel | 26,008.5 | Electric motor, Transformer and power converter | 1.92 | 49,936.3 |
| Machining | Aluminium | 424 | Electric motor, Transformer and power converter | 14.8 | 6275.2 |
| Machining | Copper | 69 | Electric motor | 3.965 | 273.6 |
| Manual | Steel | 961 | – | 1.92 | 1845.1 |

Worked out from data

#### The site's estimate

Emissions of one unit worked out by the site from its materials and energy, for the world and India, with the share of mass covered by emission factors

| Variant | Stage | Place | Emissions (kg CO2e) | Mass covered by factors |
|---|---|---|---|---|
| Machining | Making | World | 56,485 | 100% |
| Machining | Use | World | 729,545 | 100% |
| Machining | Making | India | 56,485 | 100% |
| Machining | Use | India | 1.07 million | 100% |
| Manual | Making | World | 1845 | 100% |
| Manual | Use | World | – | – |
| Manual | Making | India | 1845 | 100% |
| Manual | Use | India | – | – |

Worked out from data

#### Energy in use

Energy one unit uses per year of use, by carrier
 Energy in use

- [El Electricity](https://www.materialinsights.org/energy/electricity/) 131,610 kWh per year · lifetime 12 years Machining centre (on-mode) Table value: on-mode use of the modelled 4-axis machining centre, 30 kWh an hour for 4,387 hours a year ^[1]. The study's assumptions, not a measured average.
- [El Electricity](https://www.materialinsights.org/energy/electricity/) 1131 kWh per year · lifetime 12 years Machining centre (standby) Table value: standby use, 1.5 kWh an hour for 754 hours a year ^[1].

as of 2026-11-13. The study's own per-year rows; its total over the 12-year life is 1,592.89 MWh [1].

#### End of life

What happens to a unit when it is thrown away: collection, reuse, recycling and disposal shares, by place

| Route | Share | Place | Year | Source |
|---|---|---|---|---|
| Re-use and recycling (24.4 t of the machining centre's mass, study assumption) | 95 | EU | 2012 | ^[1] |
| Landfill (51 kg of the machining centre's mass, study assumption) | 0.2 | EU | 2012 | ^[1] |
| Thermal recycling (energy recovery), share of the plastics only, study assumption | 80 | EU | 2012 | ^[1] |

as of 2026-11-13

#### Recovered as

The commodities and chemicals recovered at end of life, with recovery rates
 Recovered as

- [St Steel](https://www.materialinsights.org/commodities/steel/) Recycling Cast iron and steel are most of the 95% of mass the study assumes is re-used or recycled ^[1]; no steel-only rate is given.

as of 2026-11-13

#### End of life in India

Collection and recycling in India, including the informal sector

The EU study assumes 95% of the machining centre's mass is re-used or recycled and 0.2% goes to landfill; for plastics it assumes 1% re-use and 80% thermal recycling ^[1]. No opened source describes the end of life of machine tools in India, informal dismantling or extended producer responsibility for them.

as of 2026-11-13

#### Water and waste

Water use and waste per unit where a source gives them

| Measure | Value | Unit | Stage | Year | Source |
|---|---|---|---|---|---|
| Water for process lubrication emulsion (use-phase table, table value) | 18 | m3 per year | Use | 2012 | ^[1] |
| Waste to landfill at end of life (machining centre) | 51 | kg | End of life | 2012 | ^[1] |

as of 2026-11-13

#### Sources

1. [Energy-Using Product Group Analysis, Lot 5, Machine tools and related machinery, Task 4 Report: Assessment of Base Case (Schischke, Hohwieler, Feitscher, König, Kreuschner, Wilpert and Nissen)](https://www.energimyndigheten.se/globalassets/energieffektivisering_/jag-ar-saljare-eller-tillverkare/dokument/produkter-med-krav/verktygsmaskiner/eup_lot5_task4_august2012_final.pdf) Fraunhofer IZM for the European Commission (DG ENTR), 2012

## Other sections

- [Summary](https://www.materialinsights.org/products/p_machine_tool/index.md)
- [Working](https://www.materialinsights.org/products/p_machine_tool/prod-working/index.md)
- [Bill of materials](https://www.materialinsights.org/products/p_machine_tool/prod-bom/index.md)
- [Use case](https://www.materialinsights.org/products/p_machine_tool/prod-use/index.md)
- [Supply chain](https://www.materialinsights.org/products/p_machine_tool/prod-supply/index.md)
- [Evolution](https://www.materialinsights.org/products/p_machine_tool/prod-evolution/index.md)
- [Interventions](https://www.materialinsights.org/products/p_machine_tool/prod-interventions/index.md)
