# Machine tool: Interventions

Source page: https://www.materialinsights.org/products/p_machine_tool/prod-interventions/

#### Interventions

Changes that would cut emissions or material use, by lever and life stage, with effect per unit, readiness, adoption, evidence and who acts

| Lever | Life stage | Change | Effect per unit | Readiness | Adoption | Who acts |
|---|---|---|---|---|---|---|
| Efficiency | Use | Combine the efficiency options the EU study assessed (for example energy recovery in the drives) | Total energy savings of 3 to 5% for the most relevant base cases at the point of least life-cycle cost ^[3]; the modelled machine without energy recovery draws about 30 kW against 25 kW for the real one ^[1] | Deployed in part; the study's options were assessed for policy | Not found in sources | Machine tool makers, regulators |
| Use less | Use | Switch off rather than leave on standby | Standby is 1,131 kWh a year against 131,610 kWh in on-mode (table values), under 1% of the total (calculated) ^[1]; the saving is small | Deployed | Not found in sources | Machine owners |
| Substitute | Use | Run machines on low-carbon electricity | Use has the highest impact in the 782 t CO2e life-cycle total of the machining centre ^[1]; the cut depends on the grid and was not calculated | Deployed where grids allow | Not found in sources | Plant operators, utilities |
| Business model | Use | Keep machines in service longer | One maker estimates an average lifetime of 15 years against 9.5 years for numerically controlled machines (VDMA), and 43% of VDW replies saw machines often above 25 years old at end of life ^[2] | Deployed | Not found in sources | Owners, makers |
| Circularity | End of life | Re-use and recycle the metal at end of life | The study already assumes 95% of mass re-used or recycled and 0.2% landfilled ^[1] | Deployed | 95% assumed in the study | Owners, recyclers |

as of 2026-11-13

#### Sources

1. [Energy-Using Product Group Analysis, Lot 5, Machine tools and related machinery, Task 4 Report: Assessment of Base Case (Schischke, Hohwieler, Feitscher, König, Kreuschner, Wilpert and Nissen)](https://www.energimyndigheten.se/globalassets/energieffektivisering_/jag-ar-saljare-eller-tillverkare/dokument/produkter-med-krav/verktygsmaskiner/eup_lot5_task4_august2012_final.pdf) Fraunhofer IZM for the European Commission (DG ENTR), 2012
2. [Energy-Using Product Group Analysis, Lot 5, Machine tools and related machinery, Task 2 Report: Economic and market analysis](https://www.energimyndigheten.se/globalassets/energieffektivisering_/jag-ar-saljare-eller-tillverkare/dokument/produkter-med-krav/verktygsmaskiner/eup_lot5_task2_august2012_final.pdf) Fraunhofer IZM for the European Commission (DG ENTR), 2012
3. [Energy-Using Product Group Analysis, Lot 5, Machine tools and related machinery, Task 7 Report: Policy and Impact Analysis](https://www.energimyndigheten.se/globalassets/energieffektivisering_/jag-ar-saljare-eller-tillverkare/dokument/produkter-med-krav/verktygsmaskiner/eup_lot5_task7_august2012_final.pdf) Fraunhofer IZM for the European Commission (DG ENTR), 2012

## Other sections

- [Summary](https://www.materialinsights.org/products/p_machine_tool/index.md)
- [Working](https://www.materialinsights.org/products/p_machine_tool/prod-working/index.md)
- [Bill of materials](https://www.materialinsights.org/products/p_machine_tool/prod-bom/index.md)
- [Use case](https://www.materialinsights.org/products/p_machine_tool/prod-use/index.md)
- [Supply chain](https://www.materialinsights.org/products/p_machine_tool/prod-supply/index.md)
- [Footprint](https://www.materialinsights.org/products/p_machine_tool/prod-footprint/index.md)
- [Evolution](https://www.materialinsights.org/products/p_machine_tool/prod-evolution/index.md)
