# PET bottle: Bill of materials

Source page: https://www.materialinsights.org/products/p_pet_bottle/prod-bom/

#### About these figures

Which unit, study and year the composition figures describe, and how they vary

Composition is for a 500 ml still-water bottle: a 12.9 g body measured on one UK bottle and a 1.6 g HDPE cap estimated in a 2020 European study ^[35]. Carbonated-drink bottles are heavier (20 to 28 g in 2009 ^[8]). The recycled variant swaps virgin resin for recycled PET. Labels, barrier layers and colourants are not covered. Components not yet nodes: the preform and the closure; both are listed as new products.

as of 2026-11-16

#### Direct materials

The commodities and chemicals in one unit as bought, with amount, mass share, cost share and recycled content
 Variant 1 **Virgin PET bottle**

| Material | Role | Amount in one unit | Share of the unit's mass | Recycled content |
|---|---|---|---|---|
| [PET PET resin](https://www.materialinsights.org/chemicals/pet/) | Structural | 0.013 kg | **89%** | 0% |
| Body resin of a 500 ml water bottle, 12.9 g as measured on one UK bottle in a 2020 European study ^[35]; mass share 12.9 of 14.5 g with the cap (calculated). The PTA, MEG and paraxylene behind it are counted in the PET resin node. |  |  |  |  |
| [HDPE High-density polyethylene](https://www.materialinsights.org/chemicals/hdpe/) | Structural | 0.002 kg | **11%** | – |
| HDPE screw cap of that bottle, 1.6 g as estimated by the study ^[35]; caps for carbonated drinks weigh about 2.4 g ^[11]. Some caps use polypropylene ^[37]. |  |  |  |  |
| [Sb Antimony](https://www.materialinsights.org/commodities/antimony/) | Functional | 0 kgrange up to 0 kg | – | – |
| Polycondensation catalyst; typically below 300 mg per kg PET ^[9], so at most about 3.9 mg in a 12.9 g body (calculated). It sits inside the resin mass, so it has no mass share of its own. |  |  |  |  |

 Variant 2 **Recycled PET bottle**

| Material | Role | Amount in one unit | Share of the unit's mass | Recycled content |
|---|---|---|---|---|
| [PET PET resin](https://www.materialinsights.org/chemicals/pet/) | Structural | 0.013 kg | **89%** | 100% |
| Same 12.9 g body ^[35] from recycled PET flake or pellets; 100% recycled content is possible ^[2]. Food-grade rPET is needed for drinks. |  |  |  |  |
| [HDPE High-density polyethylene](https://www.materialinsights.org/chemicals/hdpe/) | Structural | 0.002 kg | **11%** | – |
| Same 1.6 g cap as the virgin bottle ^[35]. |  |  |  |  |

Indicative · as of 2026-11-16

#### How it is put together

The main steps from parts and materials to the finished unit

| Step | What happens | Technology | Source |
|---|---|---|---|
| Make the monomers | Paraxylene is oxidised to purified terephthalic acid (PTA) ^[5]; monoethylene glycol (MEG) comes from ethylene. PET is made from terephthalic acid and ethylene glycol ^[9]. | – | ^[5]^[9] |
| Polymerise to resin | PTA and MEG (molar ratio 1:1.15, with about 2% isophthalic acid) react at about 280 degrees Celsius with an antimony catalyst, then in melt polymerisation at about 300 degrees Celsius ^[5] | – | ^[5] |
| Raise the chain length | Solid-state polymerisation in hot nitrogen takes about 15 hours and gives bottle-grade resin ^[5] | – | ^[5] |
| Mould the preform | Dry resin is injection moulded into a thick-walled preform with the cap thread already formed ^[12]^[9] | Injection moulding | ^[12]^[9] |
| Reheat and stretch blow | The preform is reheated, placed in a bottle mould and blown with air that stretches it outwards and downwards ^[13]. Preheating takes about 0.15 kWh per kg of preforms ^[10]. | – | ^[13]^[10] |
| Mould the cap | The cap is injection moulded from HDPE: about 1.6 g for a water bottle ^[35] and 2.4 g for a carbonated-drink cap ^[11] | Injection moulding | ^[35]^[11] |
| Fill and cap | The bottler fills the bottle and screws the cap on. Making preforms and blowing can be done in two separate stages or in one machine ^[12]. | – | ^[12] |

as of 2026-11-16

#### Technologies used to make it

The technologies used to make it, at which step
 Made with

- [IM Injection moulding](https://www.materialinsights.org/technologies/injection_moulding/) Moulding the preform and the cap Preforms are injection moulded in one-stage and two-stage machine systems ^[12]. Stretch blow moulding has no technology node yet.

as of 2026-11-16

#### Sources

1. [PET Plastic Bottles Have A Significantly Lower Environmental Impact Compared to Glass Bottles and Aluminum Cans](https://napcor.com/news/pet-plastic-bottles-have-a-significantly-lower-environmental-impact-compared-to-glass-bottles-and-aluminum-cans/) NAPCOR, 2023
2. [Decarbonisation options for the Dutch bottle-grade PET industry](https://pbl.nl/downloads/pbl-2021-decarbonisation-options-for-the-dutch-bottle-grade-pet-industry-4617pdf) PBL Netherlands Environmental Assessment Agency and TNO (Tran and West), 2021
3. [Optimising the weight of PET packaging](https://www.plastech.pl/en/news/optimising-the-weight-of-pet-packaging-2308) Plastech.pl, 2009
4. [The Facts about PET](https://petcore-europe.org/images/news/pdf/factsheet_the_facts_about_pet_dr_frank_welle_2018.pdf) Dr Frank Welle, Fraunhofer IVV (hosted by Petcore Europe)
5. [Boosting Energy and Resource Efficiency in the Manufacture of PET Bottles](https://www.petnology.com/online/news-detail/boosting-energy-and-resource-efficiency-in-the-manufacture-of-pet-bottles) KHS Corpoplast, on PETnology online, 2010
6. [New BERICAP Neck Finish According to New ISBT's PCO 1881](https://www.packaginginsights.com/news/new-bericap-neck-finish-according-to-new-isbts-pco-1881.html) Packaging Insights (CNS Media), 2006
7. [No. 9 - Stretch-Blow Molding](https://ptonline.com/articles/no-9---stretch-blow-molding) Plastics Technology (ptonline.com), sponsored by WSB Gravimetric Blenders
8. [Soda Bottle](https://www.encyclopedia.com/manufacturing/news-wires-white-papers-and-books/soda-bottle) How Products Are Made (Gale), on Encyclopedia.com
9. [Beverage packaging – A Comparative Life Cycle Assessment](https://www.ball.com/getattachment/85d9e3af-e3aa-4b93-a687-5b34888b2bfc/Ball-Comparative-2020-LCA-full-report-FINAL.pdf) Sphera for Ball Corporation, 2020
10. [Short, Shorter, the Shortest](https://www.packagingdigest.com/short-shorter-shortest) Packaging Digest (Anton Steeman), 2014

## Other sections

- [Summary](https://www.materialinsights.org/products/p_pet_bottle/index.md)
- [Working](https://www.materialinsights.org/products/p_pet_bottle/prod-working/index.md)
- [Use case](https://www.materialinsights.org/products/p_pet_bottle/prod-use/index.md)
- [Supply chain](https://www.materialinsights.org/products/p_pet_bottle/prod-supply/index.md)
- [Footprint](https://www.materialinsights.org/products/p_pet_bottle/prod-footprint/index.md)
- [Evolution](https://www.materialinsights.org/products/p_pet_bottle/prod-evolution/index.md)
- [Interventions](https://www.materialinsights.org/products/p_pet_bottle/prod-interventions/index.md)
