# Rolling bearing: Working

Source page: https://www.materialinsights.org/products/p_rolling_bearing/prod-working/

#### What it is

The product and the job it does, in a short paragraph

A rolling bearing is a pair of steel rings with balls or rollers between them. It lets one part turn against another with little friction while it carries load. This node covers ball and roller bearings (HS 8482), from small deep groove ball bearings to wind turbine main bearings. Plain (sliding) bearings and bearing housings are left out. The functional unit is one rolling bearing. The reference bearing is an NSK 6010 deep groove ball bearing: 50 mm bore, 80 mm outside diameter, 16 mm wide, about 0.261 kg ^[8].

as of 2026-11-15

#### How it works

How it does its job, step by step in plain words

An inner and an outer ring each have a hardened groove, the race. Balls or rollers run between the races, kept apart by a cage. When the shaft turns, the rolling elements roll rather than slide, so friction stays low. Load passes from the shaft through the inner ring and the rolling elements to the outer ring and the housing. Each contact patch is tiny, so the steel is very hard, about 62 to 64 HRC for standard 100Cr6 ^[15]. A thin film of grease or oil keeps the surfaces apart. Seals or shields keep grease in and dirt out, and capped bearings are filled with grease at the factory ^[14]. Designers estimate life from the basic dynamic load rating using the method in ISO 281 ^[39].

as of 2026-11-15

#### Key specifications

The numbers that describe it, each with unit, variant, year and source

| Spec | Value | Unit | Variant | Year | Source |
|---|---|---|---|---|---|
| Mass of reference bearing (NSK 6010) | 0.261 | kg | Ball | 2026 | ^[8] |
| Bore, outside diameter and width (6010) | 50 by 80 by 16 | mm | Ball | 2026 | ^[8] |
| Basic dynamic load rating (6010) | 24,000 | N | Ball | 2026 | ^[8] |
| Limiting speed with grease (6010) | 9500 | revolutions per minute | Ball | 2026 | ^[8] |
| Mass of a smaller bearing (NSK 6205, 25 by 52 by 15 mm) | 0.129 | kg | Ball | 2026 | ^[9] |
| Hardness of standard 100Cr6 rings | 62 to 64 | HRC | Ball | 2026 | ^[15] |
| Outside diameter of a double-row tapered roller (TNA) main bearing for a 5 MW turbine | 3.2 | m (approximately) | Large | 2014 | ^[27] |
| Design life of a wind turbine | 20 | years | Large | 2026 | ^[28] |

as of 2026-11-15. Mass is the maker's approximate catalogue value. The 6010C4 data page shows a pressed steel cage.

#### Variants

The variants whose make-up or footprint differs a lot, what defines each and its share of units

| Variant | Defining spec | Year | Source |
|---|---|---|---|
| Ball | Balls between the rings; the deep groove ball bearing is the commonest type and is the reference here ^[8] | 2025 | Ball bearings took 43.0% of 2025 world bearing revenue; no share of units sold found ^[1] |
| Roller | Rollers (tapered, cylindrical, spherical or needle) between the rings in place of balls | 2025 | Roller bearings took 38.0% of 2025 world bearing revenue; no share of units sold found ^[1] |
| Large | Large-size ball or roller bearings up to several metres across, for wind turbines, mining and rolling mills; Schaeffler counts those above 425 mm outside diameter as large in its remanufacturing service ^[34]^[27] | 2025 | No share found |

as of 2026-11-15

#### Limits

The physical limits set by science and the engineering limits of today's design, with today's value

| Limit | Kind | Limit | Today | Unit | Source |
|---|---|---|---|---|---|
| Operating temperature of standard 100Cr6 steel (silicon nitride rolling elements go to 700 C) | Engineering | 700 | 120 | C | ^[15] |
| Limiting speed of the 6010 (oil-bath lubrication allows more than grease) | Engineering | 11,000 | 9500 | revolutions per minute | ^[8] |
| Hardness of the ring steel (M50NiL duplex-hardened steel reaches 70 HRC) | Engineering | 70 | 64 | HRC | ^[15] |

as of 2026-11-15

#### Science it relies on

The science principles it works by or is limited by
 Relies on

- [Hooke's law of elasticity](https://www.materialinsights.org/science/hookes_law/) Balls and races flatten elastically at the contact, which spreads the load over a small area without permanent damage.
 Limited by

- [Fracture mechanics](https://www.materialinsights.org/science/fracture_mechanics/) Repeated rolling stress starts cracks below the surface and causes flaking, which sets the bearing's fatigue life.

as of 2026-11-15

#### Sources

1. [Bearings Market Size, Forecasts Report 2026-2035](https://www.gminsights.com/industry-analysis/bearings-market-report) Global Market Insights, 2026
2. [NSK 6010C4 deep groove ball bearing data page](https://www.nsk.com/engineering/6010c4-apn.html) NSK Ltd, 2026
3. [NSK 6205C2 deep groove ball bearing data page](https://www.nsk.com/engineering/6205c2-apn.html) NSK Ltd, 2026
4. [Components and materials of SKF bearings](https://coolenbearings.com/skf/tech/components-and-materials-skf-bearings) Coolen Bearings (reproducing SKF technical text)
5. [A guide to material selection for rolling bearings](https://br.bearing-news.com/?p=1444) Bearing News, 2013
6. [Designing reliable, cost effective wind turbine shaft systems](https://www.renewableenergyworld.com/wind-power/designing-reliable-cost-effective-wind-turbine-shaft-systems/) Renewable Energy World, 2014
7. [Highly Reliable Spherical Roller Bearings for Wind Turbine Main Shafts (NSK Technical Review No. 2609)](https://www.nsk.com/tools-resources/research-and-development/technical-review/2026/highly-reliable-spherical-roller-bearings-for-wind-turbine-main-shafts/) NSK Ltd, 2026
8. [Schaeffler remanufacturing makes a contribution to environmental protection](https://www.mynewsdesk.com/fi/schaeffler/blog_posts/schaeffler-remanufacturing-make-a-contribution-to-environmental-protection-remanufacturing-reduces-co2-emissions-by-up-to-95-procent-107766) Schaeffler, 2022
9. [ISO 281:2007 Rolling bearings, dynamic load ratings and rating life](https://genorma.com/en/standards/iso-281-2007/amp) ISO (via Genorma), 2007

## Other sections

- [Summary](https://www.materialinsights.org/products/p_rolling_bearing/index.md)
- [Bill of materials](https://www.materialinsights.org/products/p_rolling_bearing/prod-bom/index.md)
- [Use case](https://www.materialinsights.org/products/p_rolling_bearing/prod-use/index.md)
- [Supply chain](https://www.materialinsights.org/products/p_rolling_bearing/prod-supply/index.md)
- [Footprint](https://www.materialinsights.org/products/p_rolling_bearing/prod-footprint/index.md)
- [Evolution](https://www.materialinsights.org/products/p_rolling_bearing/prod-evolution/index.md)
- [Interventions](https://www.materialinsights.org/products/p_rolling_bearing/prod-interventions/index.md)
