# Turbocharger: Bill of materials

Source page: https://www.materialinsights.org/products/p_turbocharger/prod-bom/

#### About these figures

Which unit, study and year the composition figures describe, and how they vary

Composition follows one study of the 4A480 turbocharger, 6.5 kg, used in a Hyundai Grand Starex van (2024) ^[22]. Its table calls the turbine wheel aluminium, which is wrong for a part made of nickel superalloy ^[21], so the wheel is scaled from a BorgWarner truck unit (15.6 kg: turbine housing 8.1 kg and bearing housing 4.1 kg cast iron, compressor housing 2.3 kg aluminium) ^[24]. No better passenger-car teardown was found. Wheels, housings, actuator and bearing set are not yet nodes.

as of 2026-11-17

#### Direct materials

The commodities and chemicals in one unit as bought, with amount, mass share, cost share and recycled content

| Material | Role | Amount in one unit | Share of the unit's mass |
|---|---|---|---|
| [St Steel](https://www.materialinsights.org/commodities/steel/) | Structural | 5.105 kg | **78.5%** |
| Cast iron housings 4.655 kg (intake 0.855, exhaust 2.565, bearing 1.235) plus 0.225 kg stainless and 0.225 kg carbon steel in the actuator, from Table 1 of a 6.5 kg unit ^[22]; sums calculated. Cast iron has no node, so steel is the nearest ferrous node. |  |  |  |
| [Al Aluminium](https://www.materialinsights.org/commodities/aluminum/) | Structural | 1.08 kgrange up to 1.15 kg | **16.6%** |
| Table 1 lists 0.65 kg 'turbine wheel and other part' and 0.5 kg VNT as aluminium alloy ^[22], and the study says both are 100% aluminium. That cannot be right for the turbine wheel, which is cast in nickel superalloy such as Inconel 713C ^[21]^[18]; the aluminium is more likely the compressor wheel and cover, which are aluminium ^[21]. So 1.08 kg is 1.15 kg less the 0.07 kg wheel estimate below (calculated); high is the table's figure. |  |  |  |
| [Si Silicon](https://www.materialinsights.org/commodities/silicon/) | Functional | 0.245 kg | **3.8%** |
| Table 1 gives 'silicone' as 5% of each cast-iron housing (0.045 + 0.135 + 0.065 kg, calculated) ^[22]. A polymer making up 5% of a casting is unlikely; housings are usually SiMo (silicon-molybdenum) cast iron ^[19], so this line is read as the silicon in that iron. This reading is the checker's, not the study's. |  |  |  |
| [Ni Nickel](https://www.materialinsights.org/commodities/nickel/) | Functional | 0.07 kg | **1.1%** |
| Turbine wheel in nickel superalloy, estimate by scaling: a BorgWarner truck turbocharger of 15.6 kg has a 0.17 kg turbine wheel and shaft of Inconel 713 and steel alloy (1.1% of its mass) ^[24]; the same share of 6.5 kg is about 0.07 kg (calculated). The amount is the whole alloy; nickel is only part of it. |  |  |  |

Estimate · as of 2026-11-17

#### How it is put together

The main steps from parts and materials to the finished unit

| Step | What happens | Technology | Source |
|---|---|---|---|
| Cast the housings | Compressor cover, turbine housing and bearing housing are usually sand cast in iron or aluminium ^[34] | – | ^[34] |
| Make the wheels | The turbine wheel is investment cast from a nickel alloy; the compressor wheel is cast or milled, usually in aluminium ^[21]^[35] | Metal casting (lost wax) | ^[21]^[35] |
| Machine the shaft and parts | The shaft gets a round of high-precision machining ^[35] | Numerical control machining | ^[35] |
| Fit the bearings | The bearing assembly is added to the centre housing ^[35] | – | ^[35] |
| Join the wheels to the shaft | Wheels are slid onto the shaft and tightened ^[34] | – | ^[34] |
| Balance and inspect | Small amounts of mass are removed from the wheels or shaft to balance the set, and the assembly is checked several times ^[35]^[34] | – | ^[35]^[34] |

as of 2026-11-17

#### Technologies used to make it

The technologies used to make it, at which step
 Made with

- [Cst Metal casting (lost wax)](https://www.materialinsights.org/technologies/lost_wax_casting/) Turbine wheel casting The turbine wheel is made by an investment casting process ^[21].
- [CNC Numerical control machining](https://www.materialinsights.org/technologies/cnc_machining/) Shaft and part machining High-precision machining of the shaft is described for Honeywell turbochargers ^[35]; the source does not say numerically controlled.

as of 2026-11-17

#### Technologies inside it

The technologies inside the product, with how much of each per unit
 Embodies

- [Trb Engine exhaust recovery](https://www.materialinsights.org/technologies/e_engine_recovery/) 1 exhaust turbine and compressor set The turbocharger is the exhaust-energy recovery device that the engine recovery technology page describes.

as of 2026-11-17

#### Sources

1. [CRADA final report NFE-08-01671: Materials for Advanced Turbocharger Designs (ORNL/TM-2014/632)](https://www.osti.gov/scitech/servlets/purl/1164260) Oak Ridge National Laboratory with Honeywell (OSTI)
2. [Materials for advanced turbocharger design (merit review presentation)](https://www.energy.gov/eere/vehicles/articles/materials-advanced-turbocharger-design) US Department of Energy, Vehicle Technologies Office, 2012
3. [Anatomy of a Turbocharger: What's Inside and How it Works](https://www.cartechbooks.com/techtips/anatomy-of-a-turbocharger-whats-inside-and-how-it-works) CarTech Books
4. [Life Cycle Greenhouse Gas Reduction Effects Induced by Turbocharger Multiple Remanufacturing (preprint)](https://www.preprints.org/frontend/manuscript/bbba6b75d33b4ea701174e0fb42731de/download_pub) Preprints.org (Kim, Lee, Hwang, Kim, Kang), 2024
5. [A Business Model-LCA of turbochargers: comparing BorgWarner remanufacturing and traditional manufacturing business models (master's thesis)](https://odr.chalmers.se/bitstreams/f91c85ab-c12c-4501-99e0-934a93205945/download) Chalmers University of Technology (Malmqvist and Tiveskog), 2025
6. [From Sand To Turbocharger, Check Out How It's Made](https://www.enginelabs.com/?p=127867) Engine Labs
7. [Wheels of fortune](https://automotivemanufacturingsolutions.com/wheels-of-fortune/31265.article) Automotive Manufacturing Solutions

## Other sections

- [Summary](https://www.materialinsights.org/products/p_turbocharger/index.md)
- [Working](https://www.materialinsights.org/products/p_turbocharger/prod-working/index.md)
- [Use case](https://www.materialinsights.org/products/p_turbocharger/prod-use/index.md)
- [Supply chain](https://www.materialinsights.org/products/p_turbocharger/prod-supply/index.md)
- [Footprint](https://www.materialinsights.org/products/p_turbocharger/prod-footprint/index.md)
- [Evolution](https://www.materialinsights.org/products/p_turbocharger/prod-evolution/index.md)
- [Interventions](https://www.materialinsights.org/products/p_turbocharger/prod-interventions/index.md)
