# Recuperators and regenerators: Overview

Source page: https://www.materialinsights.org/technologies/e_recuperators/tech-overview/

#### What it does

The job the technology does for people, in a short paragraph

A furnace burns fuel to make heat, and its exhaust leaves hot. A recuperator or regenerator takes heat from that exhaust and puts it into the air the burners use, so less fuel is needed for the same heat. Robert Stirling patented the idea in 1816 ^[3] and Siemens made it work in glass and steel furnaces in the 1860s ^[1]. US Department of Energy advice is to consider heat recovery wherever furnace exhaust is hotter than 1,000°F (about 540°C) ^[6].

as of 2026-11-12

#### How it works

The working principle in plain words, step by step

A recuperator is a gas-to-gas heat exchanger on the furnace stack: hot exhaust flows on one side of a wall, cold combustion air on the other, and heat crosses the wall ^[5]^[6]. A regenerator works in turns. It is an insulated chamber filled with metal or ceramic shapes, or brick laid as a chequerwork ^[6]^[7]. Hot exhaust passes through and heats the brick. The flow is then switched, so cold air passes through the hot brick and picks up the stored heat. Because each chamber takes turns, uninterrupted operation needs at least two regenerators and their burners ^[5]. A rotary version, the Ljungström air preheater, turns a heat-storing rotor slowly between the gas and air streams ^[4]. Hotter air means a hotter flame for the same fuel, so the furnace burns less ^[5].

as of 2026-11-12

#### Key figures

The handful of numbers that size it up, each with its unit, year and source

| Figure | Value | Unit | Year | Source |
|---|---|---|---|---|
| Fuel saving from combustion air preheated to 800°F, DOE worked example | 22 | % | 2007 | ^[5] |
| Typical cut in furnace energy use from waste heat recovery, top of the 5 to 30% range | 30 | % | 2005 | ^[6] |
| Fuel saved by some early Siemens regenerative gas furnaces, up to | 50 | % | – | ^[1] |
| Highest gas temperature for metallic recuperators (2,000°F) | 1093 | °C | 2008 | ^[7] |
| Ljungström rotary air preheaters supplied worldwide, about | 20,000 | units | 1994 | ^[4] |

as of 2026-11-12. The 22% is a worked example in the 2007 DOE tip sheet, not a general rule: savings depend on exhaust and air temperature [5]. The 2005, 2007 and 2008 years are publication years. The 50% is what Grace's Guide says some early Siemens gas furnaces achieved, under its 1857 entry [1].

#### Where it is used

The main places and products the technology is found in

- Glass furnaces and coke ovens, where regenerators are most often used ^[7]
- Steel open-hearth furnaces, which used regenerators historically ^[7]
- Fuel-fired industrial furnaces fitted with a stack recuperator ^[5]^[6]
- Boilers, where Ljungström rotary air preheaters warm the combustion air ^[4]

as of 2026-11-12

#### Scale today

How much of it there is now: units in use, made each year and who uses it

**Users**
: Furnace and boiler operators in glass, steel and power

**Unit**
: units

**Year**
: 1994

**Note**
: No world count of recuperators or regenerators was found. One maker, Ljungström, had supplied about 20,000 rotary air preheaters by 1994 ^[4].

as of 2026-11-12

#### Sources

1. [William Siemens](https://www.gracesguide.co.uk/William_Siemens) Grace's Guide to British Industrial History
2. [Stirling, Robert (1790-1878)](https://encyclopedia.com/environment/encyclopedias-almanacs-transcripts-and-maps/stirling-robert-1790-1878) Macmillan Encyclopedia of Energy, via Encyclopedia.com
3. [The Ljungström Air Preheater 1920: An International Historic Mechanical Engineering Landmark](https://www.asme.org/wwwasmeorg/media/ResourceFiles/AboutASME/Who%20We%20Are/Engineering%20History/Landmarks/185-Ljungstrom-Air-Preheater.pdf) American Society of Mechanical Engineers, 1995
4. [Preheated Combustion Air, Process Heating Tip Sheet #1 (DOE/GO-102007-2482)](https://www1.eere.energy.gov/manufacturing/tech_assistance/pdfs/et_preheated.pdf) US DOE Industrial Technologies Program, 2007
5. [Install Waste Heat Recovery Systems for Fuel-Fired Furnaces, Process Heating Tip Sheet #8](https://www.energy.gov/sites/prod/files/2014/05/f16/install_waste_heat_process_htgts8.pdf) US DOE Industrial Technologies Program, 2005
6. [Waste Heat Recovery: Technology and Opportunities in U.S. Industry (BCS Inc. for US DOE Industrial Technologies Program)](https://www1.eere.energy.gov/manufacturing/intensiveprocesses/pdfs/waste_heat_recovery.pdf) US Department of Energy, 2008

## Other sections

- [Summary](https://www.materialinsights.org/technologies/e_recuperators/index.md)
- [Overview](https://www.materialinsights.org/technologies/e_recuperators/overview/index.md)
- [Correlation](https://www.materialinsights.org/technologies/e_recuperators/correlation/index.md)
- [Science and thermodynamics](https://www.materialinsights.org/technologies/e_recuperators/rc-sci/index.md)
- [Engineering and integration](https://www.materialinsights.org/technologies/e_recuperators/rc-eng/index.md)
- [Economics and contracts](https://www.materialinsights.org/technologies/e_recuperators/rc-econ/index.md)
- [Impact and additionality](https://www.materialinsights.org/technologies/e_recuperators/rc-impact/index.md)
- [What to track](https://www.materialinsights.org/technologies/e_recuperators/tracking/index.md)
- [Science](https://www.materialinsights.org/technologies/e_recuperators/tech-science/index.md)
- [Evolution](https://www.materialinsights.org/technologies/e_recuperators/tech-evolution/index.md)
- [Materials](https://www.materialinsights.org/technologies/e_recuperators/tech-materials/index.md)
- [Energy footprint](https://www.materialinsights.org/technologies/e_recuperators/tech-energy-footprint/index.md)
- [Industries](https://www.materialinsights.org/technologies/e_recuperators/tech-industries/index.md)
- [Relationships](https://www.materialinsights.org/technologies/e_recuperators/links/index.md)
