Aqueduct: Overview
What it does
The job the technology does for people, in a short paragraph
An aqueduct brings water from distant springs or rivers into a town by letting it run downhill in a built channel. Sennacherib of Assyria built one soon after 700 BCE [1], and Rome's first was begun in 312 BCE [3, 9]. Roman systems all worked by gravity, some over 64 to 80 km [8, 6]. Modern versions followed, such as the Los Angeles Aqueduct of 1913, planned at 233 miles and built to flow by gravity alone [7].
as of 2026-11-10
How it works
The working principle in plain words, step by step
Water flows downhill on its own, so an aqueduct is a long, carefully graded slope. Surveyors find a source higher than the town and set out a route that falls a little all the way, often only a few tens of centimetres per kilometre [4]. Most of the channel is a covered trench or tunnel that follows the contours of the land, which keeps the water clean and cool; of the Aqua Appia's length, almost all ran underground [3]. Where a valley is in the way, the channel is carried on arches, as at the Pont du Gard [6], or the water is sent down and up again in sealed pipes, a siphon [8]. At the town, the water enters a tank that divides it among fountains, baths and private users. Too steep a fall wastes height; too gentle and the water barely moves and drops its silt.
as of 2026-11-10
Key figures
The handful of numbers that size it up, each with its unit, year and source
| Figure | Value | Unit | Year | Source |
|---|---|---|---|---|
| Length of the Aqua Appia, Rome's first aqueduct | 11,190 | Roman paces | -312 | [3] |
| Length of the Nîmes aqueduct, which crosses the Pont du Gard | 50 | km | – | [4] |
| Average fall of the Nîmes aqueduct | 24 | cm/km | – | [4] |
| Daily water needs of Roman Nîmes met by the aqueduct | 35,000 | m3/day (about) | – | [4] |
| Length of the Los Angeles Aqueduct as recommended for construction, flowing by gravity | 233 | miles | 1913 | [7] |
as of 2026-11-10. ROMAQ gives the Nîmes fall as a mean of 0.25 m/km and a total drop of 11.2 m [5]; the museum's 24 cm/km is used here.
Where it is used
The main places and products the technology is found in
- Water supply of Roman cities, carried by gravity through aqueducts and siphons [8]
- The Pont du Gard and other bridges that carry channels across valleys [6]
- Assyrian royal water works, such as Sennacherib's aqueduct at Jerwan [1, 2]
- Modern long-distance supply to dry cities, such as the Los Angeles Aqueduct [7]
- Tunnels and canals that bring mountain water to city reservoirs
as of 2026-11-10
Scale today
How much of it there is now: units in use, made each year and who uses it
- Installed
- No world count of aqueducts was found; the Los Angeles Aqueduct alone was planned at 233 miles [7]
- Unit
- miles
- Year
- 1913
- Note
- Ancient aqueducts survive as monuments; long-distance gravity supply lines remain in use in many countries.
as of 2026-11-10
Sources
- Sennacherib's Aqueduct at Jerwan (Thorkild Jacobsen and Seton Lloyd, Oriental Institute Publications 24) Institute for the Study of Ancient Cultures, University of Chicago, 1935
- Jerwan Aqueduct (Mapping Mesopotamian Monuments, site profile) Media Center for Art History, Columbia University
- LacusCurtius • Frontinus on the Water Supply of Rome (Book I, translated by C. E. Bennett) LacusCurtius, University of Chicago (Bill Thayer)
- Visiter le Pont du Gard (Nîmes) | Musée de la Romanité Musée de la Romanité, Nîmes
- Building an Empire and a Legacy: Roman Engineering (Science and Its Times) Gale, on Encyclopedia.com
- First Owens River-Los Angeles Aqueduct American Society of Civil Engineers (ASCE)
- Building construction: Roman achievements Encyclopaedia Britannica, section Roman achievements
- Appius Claudius Caecus Encyclopaedia Britannica