Material Insights · Understanding the Material World

Control and systems: feedback, stability and how machines are made to behave

Machines are made to behave by loops that measure a result, compare it with a target and correct, and by the care taken over gain, delay and the parts around them. This module builds feedback from a tank float, a thermostat and a governor, explains proportional, integral and derivative action and why loops hunt, and works seven estimates, from a cruise control and a shower to grid frequency after a power station trips.

All courses / Understanding Engineering / Module 11

Control and systems: feedback, stability and how machines are made to behave

Machines are made to behave by loops that measure a result, compare it with a target and correct, and by the care taken over gain, delay and the parts around them. This module builds feedback from a tank float, a thermostat and a governor, explains proportional, integral and derivative action and why loops hunt, and works seven estimates, from a cruise control and a shower to grid frequency after a power station trips.

5 parts · 16 sections · about 50 minutes · 0 of 5 parts read

By the end you will be able to

  • Distinguish open-loop from closed-loop control and name the measuring, comparing and correcting steps in a thermostat, float valve or governor
  • Explain what proportional, integral and derivative action each fix and what each costs, without calculus
  • Estimate cycling, lasting error and response time for an air conditioner, a cruise control and a tank float valve
  • Explain why too much gain or too much delay makes a loop hunt, and estimate the delay in a shower pipe or the frequency fall after a power station trips
  • Use feedforward, redundancy and bottleneck reasoning to judge how a system of parts will behave
  • Describe how anti-lock brakes, autopilots, robots and solar pump controllers apply these ideas

Contents

  1. Part 1 Open loop and closed loop: measure, compare, correct

    A ceiling fan runs at the speed its regulator is set to, whatever the weather. A geyser switches itself off when the water is hot. The first obeys an instruction and never looks at the result; the second looks at the result and acts on what it sees. That difference is the core of control. This part builds it from three machines that were working long before electronics: a thermostat, a float valve and a spinning governor.

    • An open-loop machine follows its instruction blind; a closed-loop machine checks the result and corrects
    • A float valve in a water tank is a complete feedback loop made of a ball and a lever
    • A centrifugal governor holds an engine's speed by letting spinning weights swing outwards against a spring
  2. Part 2 Sensors, actuators and on-off control: the hardware of a loop

    A loop is only as good as its two ends: the sensor that reports the world and the actuator that changes it. Between them sits a decision rule, which can be as crude as a switch. This part looks at the hardware, at the simplest rule (on or off) through a room air conditioner, and at what happens when the decision-maker is a computer that sees the world only in snapshots.

    • A sensor turns a physical quantity into a signal and an actuator turns a decision into force or heat, and each limits the loop
    • On-off control is the simplest closed loop, and it cycles by design
    • A digital controller reads the world in snapshots, and a robot joint shows why inner loops must run faster than outer ones
  3. Part 3 Proportional, integral, derivative: what each action fixes and what it costs

    Most loops in factories, cars and appliances use some mix of three simple actions: push back in proportion to the error, push according to the error's running total, and push against how fast the error is changing. No calculus is needed to understand them. What matters is what each one repairs, what each one breaks, and how to tell which is missing in a loop that misbehaves.

    • Proportional action pushes back in proportion to the error, so it is quick and simple but leaves a lasting gap
    • Integral action keeps adding up the error until the gap is gone, at the price of slowness and overshoot
    • Derivative action reacts to how fast the error is changing, so it brakes early, but it magnifies noise
  4. Part 4 Stability, delay and hunting: how a loop goes wrong

    Every driver has seen it: a cruise control that surges, a shower that swings from scalding to freezing, a lamp that pulses on a weak supply. The cause is rarely a broken part. It is a loop whose corrections arrive too strongly or too late. This part explains why, works two cases with real delays, a shower pipe and a national grid, and ends with the trick of acting before the error appears.

    • A loop turns unstable when its correction is too strong or too late, and then it hunts
    • Delay is what makes loops hard: a shower at the end of a long pipe is a loop with a built-in wait
    • Grid frequency is a loop with a whole country inside it, and the spinning machines are the first line of defence
    • Feedforward acts on the disturbance before it shows in the result, and feedback cleans up what is left
  5. Part 5 Systems and the machines of today

    A control loop never stands alone. It sits in a machine whose parts interact, in a plant with a slowest stage, in a network where one failure can spread. This part starts with how aircraft handling was turned into a specification, then asks how parts combine into systems, and ends with brakes, aircraft and a solar pump that use every idea in the module.

    • Before a quality can be designed in it must be turned into numbers: how aircraft handling became a specification
    • A system is more than its parts: interactions, the slowest stage and the single point of failure decide how it behaves
    • Today's machines wrap these ideas in silicon: anti-lock brakes, autopilots and a solar pump
  6. Wrap-up Key terms, try it in the table, final quiz, sources
Start: Part 1, Open loop and closed loop: measure, compare, correct →