Control and systems: feedback, stability and how machines are made to behave: Key terms, quiz and sources
All courses / Understanding Engineering / Module 11: Control and systems: feedback, stability and how machines are made to behave Wrap-upControl and systems: feedback, stability and how machines are made to behave: review
Key terms
- Open loop
- Control that applies a fixed action without measuring the result, such as a fan regulator or a timer.
- Closed loop (feedback)
- Control that measures the result, compares it with the target and corrects, again and again.
- Set point
- The target value that a control loop tries to hold.
- Error
- The gap between the set point and the measured value.
- Disturbance
- Anything that pushes the controlled quantity off target without being asked, such as a hill or cold inflow.
- Sensor
- A device that turns a physical quantity into a signal a controller can read.
- Actuator
- A device that turns a controller's decision into force, flow or heat.
- Saturation
- The state in which an actuator is at its limit, so asking for more changes nothing.
- Hysteresis
- The gap between the switch-on and switch-off values of an on-off controller, which stops chattering.
- Gain
- The ratio of a controller's output to the error that causes it.
- Proportional action
- A push that grows in proportion to the size of the error, fast but leaving a lasting gap.
- Integral action
- A push based on the running total of the error, which removes the lasting gap but slows settling.
- Derivative action
- A push based on how fast the error is changing, which damps swings but amplifies noise.
- Windup
- Growth of the integral total while an actuator is saturated, causing a large overshoot afterwards.
- Droop
- The fall in speed or frequency as load rises under proportional governing, used to share load between machines.
- Hunting
- A sustained oscillation of a controlled quantity around its target.
- Dead time (transport delay)
- The wait between an action and its first effect, such as the time water takes to run along a pipe.
- Feedforward
- Acting on a measured disturbance before it shows up in the result.
- Bottleneck
- The slowest stage of a chain, which sets the output of the whole.
- Single point of failure
- One part whose failure stops the entire system.
Try it in the table
- Open Air conditioner and Heat pump. Using the cooling capacity you find, redo Worked estimate 2 for a room that leaks 1 kW and for one that leaks 3 kW, and say which cycles more often.
- Open Anti-lock braking. Redo the 60 km/h wet-road stopping distance for 100 km/h and say how much longer the locked-wheel stop is.
- Open Programmable logic controller and Industrial robot. Find the scan time or loop rate you would need to detect a 5 mm part moving at 1 m/s.
- Open Autopilot and Fly-by-wire flight control. List which parts are sensors, which are controllers and which are actuators, and where the duplicated computers sit.
- Open Distribution grids, mini-grids and interconnectors and Pumped hydro storage. Say which could respond within the first 3 seconds after a power station trips and which could not, and why.
- Open Centrifugal water pump and Solar PV module. Redo Worked estimate 7 for a 60 m head and a 3 kW array, and say how many hectares it irrigates.
- Open Feedback control theory and find one idea from this module in its description.
Final quiz
A hot-water geyser has a thermostat that cuts the heater when the water reaches 55 degrees C. Which part of the loop is the temperature sensor?
The sensor measures the controlled quantity and reports it back. The element is the actuator, the dial gives the set point, and the tap is a disturbance.In the roof-tank worked estimate, a tap draws 10 L/min from a tank whose float valve can pass 20 L/min when open. Why does the water stop short of the brim?
With purely proportional action the valve opens only as far as the gap below the full mark requires, so a steady draw means a steady gap.A car with a proportional cruise control gap of 5.0 km/h on a hill gets integral action added. What is the most likely result?
Integral action drives the error to zero, but the stored total must be paid down by an opposite error, so some overshoot appears and settling is slower.A bathroom shower has 1.9 L of water in the pipe between the mixing point and the head and a flow of 0.1 L/s. About how long is the delay?
Delay = volume / flow = 1.9 L / 0.1 L/s = 19 s. The user feels each tap change only after that wait.Why do engineers set a loop's gain to about half the value that would just make it oscillate?
A loop at the edge of oscillation will hunt if the process changes slightly. A gain margin of two gives a safety margin, and the price is a slower response.A 1.5 GW generator trips on a grid with 250 GW of machines and an inertia constant of 5 s. What is the initial rate of frequency fall?
Rate = 50 Hz x 1.5 GW / (2 x 5 s x 250 GW) = 0.03 Hz per second. Governors and reserves must act within seconds.What is the main strength of feedforward compared with feedback alone?
Feedforward acts on a measured disturbance early. It needs a model and cannot correct unmeasured effects, so it is paired with feedback.A line has stages of 90, 100, 120 and 150 units per minute. Which single upgrade raises output most?
The 90 stage is the bottleneck. Raising it lifts the line to 100, set by the next slowest stage. Upgrading any other stage changes nothing.Sources for this module
- Vincenti, What Engineers Know and How They Know It (Johns Hopkins University Press, 1990) · ch. 3, 'Establishment of Design Requirements: Flying-Quality Specifications for American Aircraft, 1918-1943'
- Kosky et al., Exploring Engineering (Academic Press, 2013) · ch. 8, 'Computer Engineering', sections 8.5, 8.8 and 8.10
- Kosky et al., Exploring Engineering (Academic Press, 2013) · ch. 9, 'Electrical Engineering', section 9.6, 'Switches'
- Bloomfield, How Things Work (Wiley, 2015) · ch. 1, 'The Laws of Motion, Part 1', section 1.1
- Bloomfield, How Things Work (Wiley, 2015) · ch. 2, 'The Laws of Motion, Part 2', section 2.2
- Bloomfield, How Things Work (Wiley, 2015) · ch. 3, 'Mechanical Objects Part 1', section 3.3
- Bloomfield, How Things Work (Wiley, 2015) · ch. 5, 'Fluids', section 5.2
- Bloomfield, How Things Work (Wiley, 2015) · ch. 7, 'Heat and Phase Transitions', section 7.1
- Bloomfield, How Things Work (Wiley, 2015) · ch. 8, 'Thermodynamics', section 8.1
- Bloomfield, How Things Work (Wiley, 2015) · ch. 9, 'Resonance and Mechanical Waves', section 9.1
- Bloomfield, How Things Work (Wiley, 2015) · ch. 11, 'Magnetism and Electrodynamics', section 11.2
- Åström and Murray, Feedback Systems: An Introduction for Scientists and Engineers (Princeton University Press, 2008) · ch. 10, 'PID Control', https://www.cds.caltech.edu/~murray/amwiki/PID_Control.html
- Maxwell, J. C., On Governors, Proceedings of the Royal Society of London 16 (1868) · the paper as a whole (history only)
- Central Electricity Regulatory Commission, CERC (Indian Electricity Grid Code) Regulations, 2023 (notified 29 May 2023) · Regulation 30(1) reference frequency and band; 30(9) minimum inertia; 30(10) droop and primary response, https://www.cercind.gov.in/Regulations/180-Regulations.pdf
- Central Electricity Regulatory Commission, Order in Suo Motu Petition No. 2/SM/2025 (29 March 2025), citing Grid-India's report of 17 September 2024 on high-frequency operation · web
- Grid Controller of India (Grid-India), inertia and frequency response in the Indian grid, NASPI Work Group Meeting (April 2023) · web
- Ministry of Power, as reported by All India Radio News: record peak demand of 270.82 GW (22 May 2026) · web
- Report of the Enquiry Committee on Grid Disturbance in Northern Region on 30th July 2012 and in Northern, Eastern and North-Eastern Region on 31st July 2012 (Ministry of Power, 16 August 2012) · full text at https://archive.prayaspune.org/collection/5/document/1144
- Feynman, Leighton and Sands, The Feynman Lectures on Physics, vol. I (Caltech online edition) · further reading: ch. 21, 'The Harmonic Oscillator', https://www.feynmanlectures.caltech.edu/I_21.html
- Feynman, Leighton and Sands, The Feynman Lectures on Physics, vol. I (Caltech online edition) · further reading: ch. 23, 'Resonance', https://www.feynmanlectures.caltech.edu/I_23.html
- Feynman, Leighton and Sands, The Feynman Lectures on Physics, vol. I (Caltech online edition) · further reading: ch. 24, 'Transients', https://www.feynmanlectures.caltech.edu/I_24.html