Material Insights · Understanding the Material World

Steam turbine: Interventions

Interventions

Changes that would cut emissions or material use, by lever and life stage, with effect per unit, readiness, adoption, evidence and who acts

LeverLife stageChangeEffect per unitReadinessAdoptionWho actsSource
SubstituteUseDrive the turbine with heat from geothermal wells or a nuclear reactor instead of coalPer MWh of electricity, not per turbine: about 13.9 kg CO2e for the Icelandic geothermal station and about 3 kg for Vattenfall nuclear, against 790 kg for a Chinese coal plant (about 98% lower for geothermal, calculated; boundaries differ, and the coal figure leaves out construction)DeployedCoal was 34% of world generation in 2025 [19]; thermal renewables took 3.5% of 2025 ordered capacity [1]Utilities, governments, developers[6][7][8][19][1]
EfficiencyUseRaise steam temperature and pressure with nickel alloys (advanced ultrasupercritical)Target of 47% (higher heating value) against an average of 35% for the current US coal fleet, about 26% less coal per kWh (calculated)Piloted: two nickel superalloys are commercially available after a 15-year programme ending 2015Best unit in service reaches 49.37% (LHV) with 600 degree materials [15]Makers, utilities, research consortia[16][15]
EfficiencyUseRetrofit new low-pressure turbine sections on existing plantsTwelve new low-pressure turbines add about 135 MW across two US nuclear plants (about 11 MW per turbine, calculated)DeployedNot foundPlant owners, makers[29]
DesignComponents designHalf-speed nuclear turbine with single-flow low-pressure sectionsArabelle claims 2% more power output than traditional configurationsDeployedMore than 50 units delivered or on orderMakers, nuclear utilities[13]
Change routeUseUse exhaust steam for heat in a combined heat and power system instead of condensing itTotal efficiency of about 79.6 to 79.7% (higher heating value) in the EPA's three example systems, against about 33% average electric efficiency of steam turbines in the fieldDeployedSteam turbine CHP systems are very commonly found in paper mills [4]Industrial plants, utilities[4]
DesignUseMeet India's 2.5 m3 per MWh limit on new plants with closed cooling29% less water per MWh than the 3.5 m3 limit for existing plants (calculated)DeployedRequired of new Indian coal plants from 2017Indian regulators, plant owners[18]
CircularityEnd of lifeRecycle the alloy steel of retired turbinesA geothermal life cycle study credits recycled steel at a substitution factor of 0.37 (an avoided-burden factor, not a kg CO2e figure)Modelled; no measured turbine recovery rate foundNot foundPlant owners, scrap processors[6]

as of 2026-11-15

Sources

  1. Is Steam the Answer to the Gas Turbine Bottleneck? (2025 orders, Dora Partners and McCoy Power Reports data) Turbomachinery International, 2026
  2. Catalog of CHP Technologies, Section 4: Technology Characterization, Steam Turbines US Environmental Protection Agency, CHP Partnership, 2015
  3. Life cycle assessment of the Theistareykir geothermal power plant in Iceland Elsevier (Geothermics), 2022
  4. Research on Carbon Emission Characteristics of a Typical Ultra-Low Emission Coal-Fired Power Plant Aerosol and Air Quality Research (Springer), 2025
  5. Life cycle assessments for Vattenfall's electricity generation Vattenfall, 2023
  6. Arabelle turbine for large reactors Arabelle Solutions
  7. China's Pingshan Phase II Sets New Bar as World's Most Efficient Coal Power Plant POWER Magazine, 2023
  8. Materials Matter: The Advanced Ultrasupercritical Boiler Consortium Power Engineering, 2016
  9. Emissions Control in Thermal Power Stations: Issues, Challenges, and the Way Forward The Energy and Resources Institute (TERI), 2020
  10. Global Energy Review 2026: Electricity supply IEA, 2026
  11. Is the steam turbine a key to North America's energy transition? Siemens Energy, 2025