Industrial heat pumps and vapour recompression: Overview
What it does
The job the technology does for people, in a short paragraph
Industrial heat pumps and mechanical vapour recompression (MVR) use electricity to lift heat that would be wasted to a temperature a process can use. MVR squeezes the vapour boiled off in an evaporator so it can heat that same evaporator. The idea was tried in 1857 and a plant ran at the Bex saltworks in Switzerland in 1877 [1]. Commercially available heat pumps could technically supply up to about 20% of industrial heat demand [4].
as of 2026-11-12
How it works
The working principle in plain words, step by step
An evaporator boils water out of a liquid, which gives off a large amount of warm vapour. In MVR a fan or compressor raises the vapour to the pressure and temperature needed for the evaporator's own heating steam, using a small amount of electrical energy compared with the heat in the vapour [3]. The work is usually done by single-stage centrifugal fans, which typically turn at 3,000 to 12,000 rpm [3]. A heat pump does the same for any waste heat source: a closed circuit of working fluid takes in low-temperature heat, is compressed to a higher temperature, and delivers heat to the process. Commercial high-temperature units list maximum supply temperatures from 100 to 280°C [6]. The smaller the temperature lift, the better the heat pump performs [6].
as of 2026-11-12
Key figures
The handful of numbers that size it up, each with its unit, year and source
| Figure | Value | Unit | Year | Source |
|---|---|---|---|---|
| Electricity used by MVR per tonne of water evaporated, upper end of 30 to 50 kWh | 50 | kWh per tonne | – | [3] |
| Share of industrial heat demand that commercially available heat pumps could technically supply, up to | 20 | % | 2026 | [4] |
| Installed industrial heat pump capacity in Japan, nearly | 650 | MW | 2024 | [4] |
| Share of light industry heat demand met by heat pumps, below | 1 | % | 2025 | [4] |
| Top of the maximum supply temperature range of commercial high-temperature heat pumps | 280 | °C | 2022 | [6] |
as of 2026-11-12. The 650 MW is for 2024 [4]. The 20% has no data year and 2026 is the publication year of the IEA monitor [4]; 2022 is the date of the review slides for the 280°C [6]. The 30 to 50 kWh range has no year [3].
Where it is used
The main places and products the technology is found in
- Evaporators in thermal separation plants, where MVR recycles the vapour [3]
- Food and beverage, pulp and paper, and chemical industries, judged particularly well suited [5]
- Salt production, the first home of vapour recompression at Ebensee and Bex [1][2]
- District heating, where heat pumps could play an important role [5]
as of 2026-11-12
Scale today
How much of it there is now: units in use, made each year and who uses it
- Installed
- nearly 650 MW in Japan, among the global leaders [4]
- Users
- Light industry, mainly low- and medium-temperature processes [4]
- Unit
- MW
- Year
- 2024
- Note
- The IEA says industrial adoption is growing but remains niche [4]. No world total was found.
as of 2026-11-12
Sources
- Meilensteine der Wärmepumpengeschichte Martin Zogg, Verfahrens- und Energietechnik, Oberburg (Switzerland), lecture paper
- Peter Ritter von Rittinger und das Salzkammergut: Ein Montanist als Pionier der Wärmepumpentechnik res montanarum 57, 102 to 107 (Karl Wirobal), 2017, pp. 102 to 107
- Heating options for thermal separation plants: MVR and TVR, specific utility consumption table (vendor data) GEA Group, 2026
- Heat Pump Monitor 2026: Key findings IEA, 2026
- Industrial heat pumps: Five considerations for future growth McKinsey & Company (Bauer, Ehrmaier, Gigliotti, Liebach, Schleyer, Simoncini), 2024
- IEA HPT Annex 58 about HTHPs: State of the art review, demonstration cases and development perspectives IEA Heat Pumping Technologies TCP, High-Temperature Heat Pump Symposium slides (Zühlsdorf, Poulsen, Schlosser), 29 March 2022, 2022