Material Insights · Understanding the Material World

Light, semiconductors and information: from the transistor to the network: Photons and semiconductors: diodes, solar cells and LEDs

All courses / Understanding Engineering / Module 9: Light, semiconductors and information: from the transistor to the network Part 3 of 5

Photons and semiconductors: diodes, solar cells and LEDs

A semiconductor conducts a little, and a trace of the right impurity makes it conduct a lot, in a direction you choose. This part builds that from the energy gap, forms the p-n junction, and shows that a solar cell and an LED are one device run in opposite directions, with rooftop and lamp estimates in rupees.

3.1 In a solid, electron energies form bands with a gap, and the size of the gap sorts metals, semiconductors and insulators

An isolated atom has sharp energy levels. Pack 5 x 10^22 atoms into each cubic centimetre, as in silicon, and their levels merge into broad bands, with a forbidden gap between the top filled band (the valence band) and the empty one above it (the conduction band). A full band carries no current, since an electron needs a free level to move into. In a metal the top band is only part full, so electrons move freely. In an insulator the gap is so wide that none cross. A semiconductor has a gap of about one electronvolt: silicon 1.12 eV, germanium 0.67, gallium arsenide 1.42, gallium nitride 3.4.

Room heat gives each electron on average only about 0.026 eV, far short of 1.12, but heat is shared out unevenly and a very few electrons get enough to cross. Pure silicon holds about 10^10 free electrons per cubic centimetre, one for every five million million atoms. Each electron that jumps leaves a vacancy, a hole, which moves like a positive charge as neighbours step in.

The gap also explains colour and clarity. A photon can lift an electron across only if its energy exceeds the gap. Glass has a gap near 9 eV, above every visible photon (1.8 to 3.1 eV), so visible light passes and glass is clear. Silicon's gap is 1.12 eV, below visible photons, so they are all absorbed and the wafer is a grey mirror; but a photon of wavelength above 1,100 nm, below the gap, passes, so silicon is transparent to infrared. A photon absorbed this way makes a free electron and hole pair, which is the heart of a solar cell and of the photodiode that reads the light at the end of an optical fibre (see 'Photovoltaic effect').

  • Bloomfield, How Things Work (Wiley, 2015) · ch. 13, 'Light', section 'LEDs and Lasers' (levels in solids, band structure, metals, insulators and semiconductors)

3.2 Doping makes silicon conduct by electrons or holes, and a p-n junction passes current one way only

Silicon atoms share four outer electrons with four neighbours. Replace one atom in five million with phosphorus, which has five, and the extra electron is loosely held and free to wander: n-type silicon. Replace one in five million with boron, which has three, and each leaves a hole: p-type silicon. That concentration, about 10^16 atoms per cubic centimetre, is 0.2 parts per million. It gives a million times more carriers than heat makes alone.

Join a p-type region to an n-type one. Electrons spill across into the p side and holes into the n side, leaving fixed, charged atoms behind. Their field, across a thin depletion layer, pushes further crossing back. The field stops growing when it holds a built-in voltage of about 0.7 V for doping of 10^16 on each side: 0.026 V x ln(10^16 x 10^16 / (10^10)^2) = 0.026 x 27.6 = 0.72 V. Connect a battery with its positive end to p, and it reduces the barrier; current rises by a factor of ten for every 60 millivolts. Reverse it, and the barrier grows and only a trickle of leakage flows. That is a diode, a non-return valve for current.

A bridge of four diodes turns alternating current into direct, and a solar module carries three more in its junction box as bypass diodes. If a leaf shades one string of cells, that string stops passing current and the bypass diode carries the module's current round it. These are Schottky diodes, metal-on-silicon junctions with a drop of about 0.45 V, yet at 13 A one still turns 0.45 V x 13 A = 5.9 W into heat inside a small sealed box, while the bypassed third of the module, about 180 W of a 550 W rating, produces nothing. Hence junction boxes are designed around their diodes, and some makers fit active bypass circuits built from transistor switches, which Part 4 explains.

Data Pure and doped silicon at room temperature (round figures)
SiliconFree carriers per cm3ResistivityHow made
Pureabout 10 thousand million (10^10) electrons and as many holesabout 300,000 ohm cmHeat alone lifts electrons
n-type, one phosphorus atom per 5 millionabout 10^16 electronsabout 0.5 ohm cmPhosphorus gives a free electron
p-type, one boron atom per 5 millionabout 10^16 holesabout 1.4 ohm cmBoron leaves a hole
Copper, for comparisonabout 8 x 10^22 electronsabout 0.0000017 ohm cmMetal bonding

Resistivity = 1 / (charge x carriers x mobility), calculated with mobilities of about 1,350 (electrons) and 450 (holes) cm2 per volt second. Doping thus changes resistivity by a factor of about a million and can be set between wide limits by ion implantation.

Source: Bloomfield, How Things Work (Wiley, 2015), ch. 13, 'Light' (p-n junction, diodes); ch. 14, 'Optics and Electronics' (transistors); numbers computed by the author from standard values
  • Bloomfield, How Things Work (Wiley, 2015) · ch. 13, 'Light', section 'LEDs and Lasers' (p-n junction, diodes)

3.3 A solar cell is a junction that sorts light-made electrons and holes into a current, and a rooftop estimate checks its size

Shine light on the junction. Each photon above the gap makes an electron and a hole near the depletion field, and the field sweeps the electron to the n side and the hole to the p side. The field provides a voltage of no more than the gap allows, in practice about 0.6 to 0.7 V per cell. That is why modules are strings of cells in series, like batteries in a torch.

Two losses cap the efficiency. A photon below the gap does nothing. A photon well above it makes one pair and wastes the excess as heat. Balancing them gives a best single-gap efficiency of about 33 per cent; for silicon, once losses inside the crystal itself are counted, the ceiling is about 29.4 per cent. In April 2025 LONGi reported a silicon cell certified at 27.81 per cent and a silicon-perovskite tandem at 34.85 per cent, and in 2026 it raised these to 28.13 per cent (certified by ISFH) and 35.5 per cent (certified by ESTI). Commercial modules sell at 21 to 23 per cent. A tandem stacks a wide-gap layer for blue light on a narrow-gap one for red.

The table redoes the numbers for one cell of 182 mm side, the common size in Indian module factories. As a cross-check, the most current a silicon cell can give from sunlight is about 43 mA per square centimetre, or 14 A over this cell. Our 12 A is 85 per cent of that ceiling.

The cell is a heat source too: about three quarters of the sunlight ends as heat, and silicon loses about 0.3 per cent of its power for every degree it runs above 25 degrees C. A rooftop module at 60 degrees C therefore delivers about 10 per cent less than its rating.

Data Estimate 4: current from one solar cell, and a rooftop module's daily yield
StepWorkingResult
Cell area0.182 m x 0.182 m0.033 m2
Sunlight on it, bright noon1,000 W/m2 x 0.033 m233 W
Electrical power at 22 per cent33 W x 0.227.3 W
Current at 0.6 V7.3 W / 0.6 Vabout 12 A
Ceiling from photon count0.043 A/cm2 x 331 cm2about 14 A
Check: a 550 W module of 144 half-cellsdatasheet current near its power pointabout 13 A at 42 V
Heat left in the cell33 W - 7.3 Wabout 26 W
Module yield per day0.55 kW x 5 peak sun hours x 0.8about 2.2 kWh
Per year2.2 kWh x 365about 800 kWh

A peak sun hour is one hour of 1,000 W/m2; most of India receives about 4 to 6 a day. The factor 0.8 covers heat, wiring, dust and inverter losses.

Source: LONGi Green Energy press releases: '34.85%! LONGi Breaks World Record for Crystalline Silicon-Perovskite Tandem Solar Cell Efficiency Again' (21 April 2025); '28.13%, 26.4%! LONGi Sets New World Records' (28 April 2026); '35.5%! LONGi Once Again Breaks World Record' (14 July 2026); read November 2026, 27.81 per cent HIBC silicon (ISFH) and 34.85 per cent tandem (NREL) in 2025; 28.13 per cent (ISFH) and 35.5 per cent (ESTI) in 2026; https://www.longi.com/us/news/longi-world-record-crystalline-silicon-perovskite/, https://www.longi.com/en/news/hybrid-interdigitated-back-contact-cell-record/, https://www.longi.com/en/news/crystalline-silicon-perovskite-tandem-solar-cell-new-world-efficiency-2026/; table arithmetic by the author
  • Bloomfield, How Things Work (Wiley, 2015) · ch. 13, 'Light' (photoconductors, p-n junction)
  • Richter, A., Hermle, M. and Glunz, S. W., 'Reassessment of the Limiting Efficiency for Crystalline Silicon Solar Cells', IEEE Journal of Photovoltaics 3(4), 2013 · limiting efficiency of about 29.4 per cent for a silicon cell

3.4 Run the same junction forward and electrons fall across the gap and shine, so an LED beats a filament several times over

Forward-bias a p-n junction and electrons and holes are driven together at the junction. When one meets the other the electron drops across the gap and the energy leaves as a photon, of energy about equal to the gap. So the colour is fixed by the material: wavelength in nm = 1,240 / gap in eV. Red LEDs (aluminium gallium indium phosphide) have a gap of about 1.9 to 2.0 eV; the blue ones that made white lamps possible use indium gallium nitride, near 2.7 eV, which won its inventors the 2014 Nobel Prize. Silicon is a poor emitter: its gap is the indirect kind, where crossing also needs a shake from the crystal, so the electron mostly gives up its energy as heat. White LEDs use a blue chip with a yellow phosphor; some energy is lost in the conversion, the price of a single cheap chip.

A filament lamp is a hot wire at about 2,700 K, and most of what it radiates is infrared. For a given brightness, measured in lumens, an incandescent lamp gives roughly 12 lm per watt, while a good LED lamp gives about 100. The ideal for white light is near 300. In other words only about 4 per cent of a filament's electricity makes light that the eye uses, against roughly a third in an LED.

The table sets a room used 4 hours a day against each lamp. The saving, ₹685 a year per lamp, adds up: every 10 crore filament lamps replaced saves about 8.6 TWh a year, roughly half of one per cent of the 1,850 TWh India generated in 2025-26. India has already made much of this swap: its UJALA programme had distributed 36.78 crore LED bulbs by January 2022, which the Ministry of Power estimated saves about 48 billion kWh a year.

Data Estimate 5: one 800 lumen lamp, 4 hours a day, at ₹8 per kWh
QuantityFilament lampLED lampIdeal white light
Light output per watt12 lm/W100 lm/Wabout 300 lm/W
Power for 800 lm67 W8 W2.7 W
Energy a year (1,460 hours)97 kWh11.7 kWh3.9 kWh
Cost a year₹780₹93₹31
Rated lifeabout 1,000 hoursabout 25,000 hoursnot applicable
Saving by switching-86 kWh and ₹685 a year-
10 crore lamps switched-about 8.6 TWh a year (0.46 per cent of 1,850 TWh)-

All values calculated. Efficacy values are typical figures for a 230 V filament lamp and a retail LED lamp; the ideal is for a phosphor-type white spectrum. Site pages: 'LED lamp', 'Display panel (LCD and OLED)' and 'Lighting and displays'.

Source: Bloomfield, How Things Work (Wiley, 2015), ch. 13, 'Light' (illumination, LEDs); numbers computed by the author
  • Bloomfield, How Things Work (Wiley, 2015) · ch. 13, 'Light', section 'LEDs and Lasers' (light-emitting diodes)
  • Press Information Bureau, Ministry of Power, UJALA release (5 January 2022, read November 2026) · 36.78 crore LED bulbs distributed; about 47.78 billion kWh saved a year; https://pib.gov.in/PressReleasePage.aspx?PRID=1787594
  • Ministry of Power, Government of India, 'Power Sector at a Glance' (data up to March 2026, read November 2026) · total generation 1,847.9 BU in 2025-26 and 1,829.7 BU in 2024-25; https://powermin.gov.in/sites/default/files/uploads/power_sector_at_glance_deleted_.pdf and https://powermin.gov.in/sites/default/files/uploads/power_sector_at_glance_Sep_2025.pdf

See it in the table

Al AluminiumSi SiliconGa GalliumGe GermaniumIn IndiumB BoronEl Electricity

Check your understanding

Why is window glass clear to visible light but a silicon wafer opaque?

A photon is absorbed only if it can lift an electron across the gap. Visible photons (1.8 to 3.1 eV) cannot cross glass's gap but easily cross silicon's.

What makes n-type silicon different from pure silicon?

Phosphorus has five outer electrons, four bond and one is free. At one atom in five million it raises free carriers about a million times.

A 182 mm cell receives 1,000 W/m2 and is 22 per cent efficient. Working at 0.6 V, about what current does it give?

Area 0.033 m2 gives 33 W of light, 7.3 W of electricity, and 7.3 / 0.6 is about 12 A.
← Part 2: Light, lenses and optical fibreMark read · Part 4: The transistor and the integrated circuit →