Material Insights · Understanding the Material World

Earth's surface: land, water, ice and erosion: Building the relief: folds, faults, mountains, plains and deserts

All courses / Understanding Science / Module 19: Earth's surface: land, water, ice and erosion Part 1 of 6

Building the relief: folds, faults, mountains, plains and deserts

Land is the result of a contest. Heat from inside the Earth and the push of plates lift it, and water, ice, gravity and wind wear it down. This part reads what the lifting leaves: folds, faults, mountains, plains, plateaus and deserts.

1.1 Folds and faults record whether the crust was squeezed, stretched or sheared

Road cuttings on the hill roads below Shimla show beds of rock bent into arches and troughs. Stress is force per unit area, and the crust feels three kinds: compression squeezes, tension pulls apart and shear drags one side past the other. Module 18 linked them to the kinds of plate boundary and explained why deep, warm rock bends while cold, shallow rock breaks.

Under a small stress, rock deforms elastically and springs back when the load is removed, which is how strain stores up before an earthquake. Past its elastic limit it either deforms plastically, keeping its new shape, or fractures. Which happens depends on the rock, its temperature, the confining pressure and how fast the load comes.

A fold that arches upward is an anticline, and one that sags downward is a syncline. Once erosion has planed the top off, the beds at the surface tell them apart: an anticline exposes its oldest beds along its axis, a syncline its youngest.

A fault is a fracture along which the two sides have slid. Where the fault surface slopes, the block above it is the hanging wall and the block beneath is the footwall. In a normal fault, tension lets the hanging wall drop. In a reverse fault, compression drives it up, and a low-angle reverse fault is a thrust, the main structure of the Himalaya. In a strike-slip fault the blocks move sideways, and in an oblique fault the motion combines sideways and vertical slip. So the faults in a quarry face say which stress acted there, long after the boundary that caused it has gone.

  • Hewitt, Lyons, Suchocki and Yeh, Conceptual Integrated Science, 2nd edition (Pearson, 2013) · ch. 24, 'Earth's Surface: Land and Water'

1.2 Mountains come in four kinds, and the Himalaya is one kind while the Western Ghats are another

Mountains are classified by how they were built. Fold mountains form where plates converge and squeeze a thick pile of strata into arches and thrust slices. The Himalaya, the Alps and the Andes are of this kind. They are the highest and longest ranges, because convergence shortens and thickens the crust, and a thick crust floats high, as isostasy requires. The Aravalli range is also a fold mountain, but a very ancient one, now worn to low ridges (module 18).

Fault-block mountains form where tension or compression breaks the crust along faults and lifts some blocks above their neighbours. In India, the Narmada valley lies in a long trough between two blocks, the Vindhya and Satpura ranges.

Volcanic mountains are piles of lava and ash built up round a vent, as at Mount Fuji. Dome, or upwarped, mountains are broad bulges where pressure from below, often rising magma, arches the strata; erosion then strips the softer cover and leaves rings of tilted layers round a hard core, as in the Ozark dome of the central United States.

The Western Ghats do not fit the first group neatly. They are better seen as the raised edge of the peninsula, left as a long escarpment when the continent rifted from Madagascar and the Seychelles and the western margin was uplifted. The steep western face catches the monsoon, which is why weathering and landslides are so active there.

Data Four kinds of mountain and an Indian reading of each
KindHow it formsExampleWhat to look for
FoldCompression at a plate collisionHimalaya (young), Aravalli (very old)Folded strata, thrust faults, high peaks
Fault-blockCrust broken by faults, blocks tilted or raisedBasin and Range, Narmada troughSteep straight fronts beside flat valleys
VolcanicLava and ash piling round a ventFuji, KilimanjaroA cone with a crater
Dome (upwarped)Upward bulge of strata, top erodedOzark domeRings of tilted layers round a core

The Deccan plateau and its volcanic origin are described in module 18.

Source: Hewitt, Lyons, Suchocki and Yeh, Conceptual Integrated Science, 2nd edition (Pearson, 2013), ch. 24, 'Earth's Surface: Land and Water'
  • Hewitt, Lyons, Suchocki and Yeh, Conceptual Integrated Science, 2nd edition (Pearson, 2013) · ch. 24, 'Earth's Surface: Land and Water'

1.3 Plains are built by deposition, plateaus are lifted flat, and deserts are shaped by the wind

A plain is a broad, low and nearly flat stretch of land. Most are built from sediment dropped by rivers. The Indo-Gangetic plain is the standard case: it is a trough in front of the Himalaya, filled over millions of years by sand, silt and clay from rivers cutting the mountains, to a depth of kilometres in places. A plateau is a flat region standing high above its surroundings, bounded by steep edges on at least one side. It arises when a large block of crust is raised without much deformation, as the Tibetan plateau was by the collision of India and Asia, or when flows of lava fill an old landscape, as in the Deccan.

Wind is a weaker agent than water, and it matters most where plant cover is thin. It does three things. It lifts and removes fine particles, which is deflation, leaving a pavement of stones. It sandblasts rock with the grains it carries, which is abrasion. It drops its load as dunes, ridges of sand that move downwind because grains hop up the gentle face and fall down the steep one. Fine dust travels far and settles as loess, a soft yellow silt that makes fertile soil.

In the Thar desert, dunes march with the monsoon winds and can bury fields and canals when grass cover is lost, so planting grass and trees to hold the sand is the main defence.

  • Hewitt, Lyons, Suchocki and Yeh, Conceptual Integrated Science, 2nd edition (Pearson, 2013) · ch. 24, 'Earth's Surface: Land and Water'
  • Hewitt, Lyons, Suchocki and Yeh, Conceptual Integrated Science, 2nd edition (Pearson, 2013) · ch. 25, 'Surface Processes'

See it in the table

H₂O Water

Check your understanding

After erosion, an anticline can be recognised at the surface by

An anticline arches the beds upward, so once the top is worn off the oldest beds lie in the core. A syncline shows the youngest beds in its core.

A reverse or thrust fault is produced by

In reverse faults the crust is shortened, which is the pattern of the Himalaya. Tension makes normal faults.

Low, rounded ridges like the Aravalli are best explained as

Erosion lowers any range given enough time, so a low and rounded profile suggests great age.
← Module contentsMark read · Part 2: Rock into soil, and soil down the slope →