Ceiling fan: Bill of materials
About these figures
Which unit, study and year the composition figures describe, and how they vary
The direct materials are for a good quality 1,200 mm induction fan listed by NRCD (2005) and quoted by Prayas: 1.1 kg of silicon steel stampings, 0.3 kg of copper wire and 2.2 kg of end-shield castings, plus a shaft, two bearings, a rotor casting, two canopies, a capacitor and three blades [5]. Complete fans weigh 4.53 kg (Havells induction) and 5 kg (Atomberg BLDC) [7][10]. The fan motor is counted here, not linked, because the motor node describes much larger motors. Capacitors, regulators and controller boards are not yet product nodes.
as of 2026-11-17
Components
The products inside one unit, with quantity, mass share and cost share
Variant BLDC| Material | Role | Amount in one unit | Share of the unit's mass |
|---|---|---|---|
| Permanent magnet | Component | Not given | – |
| A BLDC rotor carries permanent magnets; ferrite magnets are available in India, while Usha's chief executive said in 2023 that the magnets were imported [16][17]. | |||
as of 2026-11-17
Direct materials
The commodities and chemicals in one unit as bought, with amount, mass share, cost share and recycled content
Variant 1 Induction| Material | Role | Amount in one unit | Share of the unit's mass |
|---|---|---|---|
| Al Aluminium | Structural | 2.2 kg | – |
| End-shield castings (the motor covers) of the same fan [5]. Prayas does not name the alloy; Indian makers die cast motor covers and rotor cages in aluminium [22], so the amount is indicative. Rotor and blade mass is not given. | |||
| St Steel | Functional | 1.1 kg | – |
| Silicon steel stampings (the motor laminations) of a good quality 1,200 mm induction fan, from an NRCD (2005) list quoted by Prayas [5]. Steel in the shaft, downrod and canopies is not given [5][22]. | |||
| Cu Copper | Functional | 0.3 kg | – |
| Copper winding wire in the same 1,200 mm induction fan [5]. Some newer fans use aluminium or copper-clad aluminium windings instead [30]. | |||
| Material | Role | Amount in one unit | Share of the unit's mass |
|---|---|---|---|
| ABS ABS | Structural | Not given | – |
| The blades of the Havells Stealth Air BLDC fan are compounded ABS [8]; the Atomberg Renesa Alpha has aluminium blades [10]. No source gives the mass. | |||
| Material | Role | Amount in one unit | Share of the unit's mass |
|---|---|---|---|
| Pnt Paints and coatings | Functional | Not given | – |
| Parts are pretreated and powder coated [22]; Havells lists a powder coated finish [7]. No source gives the mass. | |||
Indicative · as of 2026-11-17. Masses are for one good quality 1,200 mm induction fan in an NRCD (2005) list quoted by Prayas [5]; no source opened gives masses for a BLDC fan.
Cost breakdown
The share of the unit's cost in each component or stage
| Part | Share of cost | Variant | Year | Source |
|---|---|---|---|---|
| Copper winding wire (18 to 25% of a model plant's operating cost, not of one fan; midpoint, calculated) | 21.5% | – | 2026 | [22] |
| Aluminium ingot and sheet (15 to 22%; midpoint, calculated) | 18.5% | – | 2026 | [22] |
| Electronics and components such as capacitors, bearings and BLDC drivers (12 to 20%; midpoint, calculated) | 16% | – | 2026 | [22] |
| CRNO electrical steel for laminations (10 to 15%; midpoint, calculated) | 12.5% | – | 2026 | [22] |
| Powder, paint and packaging (5 to 8%; midpoint, calculated) | 6.5% | – | 2026 | [22] |
| Materials of a good quality 1,200 mm fan (INR 445 of INR 525; calculated) | 84.8% | Induction | – | [5] |
| Labour including painting (INR 45 of INR 525; calculated) | 8.6% | Induction | – | [5] |
| Packing (INR 35 of INR 525; calculated) | 6.7% | Induction | – | [5] |
as of 2026-11-17
How it is put together
The main steps from parts and materials to the finished unit
| Step | What happens | Source |
|---|---|---|
| Stamp and stack laminations | Electrical steel is stamped into laminations, which are stacked and riveted into cores. | [22] |
| Die cast | Aluminium rotor cages and motor covers are cast. | [22] |
| Machine | Covers and shafts are machined for bearing fits. | [22] |
| Wind and varnish | Copper coils are wound, inserted and impregnated. | [22] |
| Form blades and parts | Blades, downrods and canopies are formed. | [22] |
| Finish | Parts are pretreated and powder coated. | [22] |
| Assemble motor and fan | Stator, rotor, bearings and a capacitor or driver are fitted. | [22] |
| Test and pack | Air delivery, power, safety and balance are checked, then fans are cartoned and shipped. | [22] |
as of 2026-11-17
Technologies inside it
The technologies inside the product, with how much of each per unit
Embodies- Mot Electric motors and drives 1 motor per fan Each fan embodies one small electric motor, induction or BLDC.
- PE Transformers and power electronics A BLDC fan carries a controller board that switches the coil current; the controller is the main extra cost of a BLDC motor over an induction motor [6].
as of 2026-11-17
Sources
- Ceiling Fan: The Overlooked Appliance in Energy Efficiency Discussions (Singh, Barve, Sant) Prayas Energy Group, Pune, Annexure, Table A-1
- Efficiency improvement opportunities for ceiling fans (Shah, Sathaye, Phadke, Letschert), vol. 8, pp. 37 to 50 Energy Efficiency, Springer, 2015
- Xpress HS Regular Ceiling Fan Havells India
- Stealth Air BLDC+ Ceiling Fan Havells India
- Atomberg Renesa Alpha 120cm Sweep 3 Blade Ceiling Fan, 5 Star BEE Rated Croma
- Experts Discuss Advancing Affordable, Energy-Efficient, and Locally Produced Ceiling Fans in India Natural Resources Defense Council (NRDC)
- Ceiling fans get costlier by 8 to 20 per cent as BEE's revised norms mandate star labelling The Tribune (PTI), 2023
- Ceiling fan plant setup cost in India: manufacturing process flow, machinery, DPR and financial model 2026 IMARC Group, 2026
- Why Your Parents' Fan Still Works? And Yours Won't! (newsletter, March 2025) International Copper Association India (ICA India), 2025