Turbocharger: Bill of materials
About these figures
Which unit, study and year the composition figures describe, and how they vary
Composition follows one study of the 4A480 turbocharger, 6.5 kg, used in a Hyundai Grand Starex van (2024) [22]. Its table calls the turbine wheel aluminium, which is wrong for a part made of nickel superalloy [21], so the wheel is scaled from a BorgWarner truck unit (15.6 kg: turbine housing 8.1 kg and bearing housing 4.1 kg cast iron, compressor housing 2.3 kg aluminium) [24]. No better passenger-car teardown was found. Wheels, housings, actuator and bearing set are not yet nodes.
as of 2026-11-17
Direct materials
The commodities and chemicals in one unit as bought, with amount, mass share, cost share and recycled content
| Material | Role | Amount in one unit | Share of the unit's mass |
|---|---|---|---|
| St Steel | Structural | 5.105 kg | 78.5% |
| Cast iron housings 4.655 kg (intake 0.855, exhaust 2.565, bearing 1.235) plus 0.225 kg stainless and 0.225 kg carbon steel in the actuator, from Table 1 of a 6.5 kg unit [22]; sums calculated. Cast iron has no node, so steel is the nearest ferrous node. | |||
| Al Aluminium | Structural | 1.08 kgrange up to 1.15 kg | 16.6% |
| Table 1 lists 0.65 kg 'turbine wheel and other part' and 0.5 kg VNT as aluminium alloy [22], and the study says both are 100% aluminium. That cannot be right for the turbine wheel, which is cast in nickel superalloy such as Inconel 713C [21][18]; the aluminium is more likely the compressor wheel and cover, which are aluminium [21]. So 1.08 kg is 1.15 kg less the 0.07 kg wheel estimate below (calculated); high is the table's figure. | |||
| Si Silicon | Functional | 0.245 kg | 3.8% |
| Table 1 gives 'silicone' as 5% of each cast-iron housing (0.045 + 0.135 + 0.065 kg, calculated) [22]. A polymer making up 5% of a casting is unlikely; housings are usually SiMo (silicon-molybdenum) cast iron [19], so this line is read as the silicon in that iron. This reading is the checker's, not the study's. | |||
| Ni Nickel | Functional | 0.07 kg | 1.1% |
| Turbine wheel in nickel superalloy, estimate by scaling: a BorgWarner truck turbocharger of 15.6 kg has a 0.17 kg turbine wheel and shaft of Inconel 713 and steel alloy (1.1% of its mass) [24]; the same share of 6.5 kg is about 0.07 kg (calculated). The amount is the whole alloy; nickel is only part of it. | |||
Estimate · as of 2026-11-17
How it is put together
The main steps from parts and materials to the finished unit
| Step | What happens | Technology | Source |
|---|---|---|---|
| Cast the housings | Compressor cover, turbine housing and bearing housing are usually sand cast in iron or aluminium [34] | – | [34] |
| Make the wheels | The turbine wheel is investment cast from a nickel alloy; the compressor wheel is cast or milled, usually in aluminium [21][35] | Metal casting (lost wax) | [21][35] |
| Machine the shaft and parts | The shaft gets a round of high-precision machining [35] | Numerical control machining | [35] |
| Fit the bearings | The bearing assembly is added to the centre housing [35] | – | [35] |
| Join the wheels to the shaft | Wheels are slid onto the shaft and tightened [34] | – | [34] |
| Balance and inspect | Small amounts of mass are removed from the wheels or shaft to balance the set, and the assembly is checked several times [35][34] | – | [35][34] |
as of 2026-11-17
Technologies used to make it
The technologies used to make it, at which step
Made with- Cst Metal casting (lost wax) Turbine wheel casting The turbine wheel is made by an investment casting process [21].
- CNC Numerical control machining Shaft and part machining High-precision machining of the shaft is described for Honeywell turbochargers [35]; the source does not say numerically controlled.
as of 2026-11-17
Technologies inside it
The technologies inside the product, with how much of each per unit
Embodies- Trb Engine exhaust recovery 1 exhaust turbine and compressor set The turbocharger is the exhaust-energy recovery device that the engine recovery technology page describes.
as of 2026-11-17
Sources
- CRADA final report NFE-08-01671: Materials for Advanced Turbocharger Designs (ORNL/TM-2014/632) Oak Ridge National Laboratory with Honeywell (OSTI)
- Materials for advanced turbocharger design (merit review presentation) US Department of Energy, Vehicle Technologies Office, 2012
- Anatomy of a Turbocharger: What's Inside and How it Works CarTech Books
- Life Cycle Greenhouse Gas Reduction Effects Induced by Turbocharger Multiple Remanufacturing (preprint) Preprints.org (Kim, Lee, Hwang, Kim, Kang), 2024
- A Business Model-LCA of turbochargers: comparing BorgWarner remanufacturing and traditional manufacturing business models (master's thesis) Chalmers University of Technology (Malmqvist and Tiveskog), 2025
- From Sand To Turbocharger, Check Out How It's Made Engine Labs
- Wheels of fortune Automotive Manufacturing Solutions