Vehicle transmission: Bill of materials
About these figures
Which unit, study and year the composition figures describe, and how they vary
Composition is the transmission and clutch of the average conventional midsize car in Argonne's 2020 GREET update, 87.4 kg from A2Mac1 teardowns, with no oil column [4]. Oil volumes come from one Volvo XC60 (2014) [15]. Chromium, manganese, nickel and molybdenum are inside the steel and are not given by mass. Electric-car transmissions (20.2 to 23.8 kg) have no published bill of materials [5]. Plastics (2.59 kg), glass fibre composite (0.78 kg) and rubber (0.23 kg) are not linked. The clutch and drive axle are not yet nodes.
as of 2026-11-17
Components
The products inside one unit, with quantity, mass share and cost share
| Material | Role | Amount in one unit | Share of the unit's mass |
|---|---|---|---|
| Rolling bearing | Component | Not given | – |
| Gearbox shafts run on rolling bearings; a life-cycle study of a single-stage industrial gearbox models its shaft bearings separately [16]. No source gives the count or mass per car gearbox, and bearing steel is already inside the GREET steel figure, so no quantity is given. | |||
as of 2026-11-17
Direct materials
The commodities and chemicals in one unit as bought, with amount, mass share, cost share and recycled content
Variant 1 Not stated| Material | Role | Amount in one unit | Share of the unit's mass |
|---|---|---|---|
| St Steel | Structural | 57.99 kg | 66.3% |
| 127.85 lb of steel in the transmission and clutch of the average conventional car in GREET, converted to kg (calculated); gears and shafts are case-hardened alloy steel [4][17]. | |||
| Al Aluminium | Structural | 24.38 kg | 27.9% |
| Cast aluminium 19.88 kg (casing) plus wrought aluminium 4.50 kg, from 43.83 lb and 9.92 lb (calculated) [4]. | |||
| Cu Copper | Functional | 1.44 kg | 1.7% |
| 3.18 lb in the same row, converted (calculated) [4]. | |||
| Cr Chromium | Functional | Not given | – |
| Alloying element of carburising gear steels such as 20MnCr5 [17]; counted inside the steel above, no amount found. | |||
| Mn Manganese | Functional | Not given | – |
| Alloying element of carburising gear steels such as 20MnCr5 [17]; counted inside the steel, no amount found. | |||
| Ni Nickel | Functional | Not given | – |
| Alloyed in nickel-molybdenum gear steels such as 20NiMo9-7 [17]; counted inside the steel, no amount found. | |||
| Mo Molybdenum | Functional | Not given | – |
| Used mainly as an alloying agent in steel [31]; counted inside the steel, no amount found. | |||
| Lub Lubricant additives | Consumable | Not given | – |
| Oil carries additives for wear and friction control; no amount found. | |||
| Material | Role | Amount in one unit | Share of the unit's mass |
|---|---|---|---|
| Oil Crude oil | Consumable | 1.9 L | – |
| Transmission oil fill of about 1.9 litres with the D4204T5 engine (about 1.45 litres with others) [15]; base oil is refined from crude oil and has no node of its own. | |||
| Material | Role | Amount in one unit | Share of the unit's mass |
|---|---|---|---|
| Oil Crude oil | Consumable | 7.3 L | – |
| Transmission fluid fill of about 7.3 litres [15]. | |||
as of 2026-11-17
How it is put together
The main steps from parts and materials to the finished unit
| Step | What happens | Technology | Source |
|---|---|---|---|
| Shape gear blanks | Alloy steel bar is forged or machined into gear and shaft blanks. | – | – |
| Cut the teeth | Machines cut the gear teeth to shape on computer-controlled tools. | Numerical control machining | – |
| Case-harden | Gears are heated in a carburising atmosphere so the surface becomes hard and the core stays tough [17]. | – | [17] |
| Finish | Hardened gears often need post-treatment such as shot peening or grinding [17]. | – | [17] |
| Cast the housing | Molten aluminium is cast into the casing; 19.88 kg of cast aluminium sits in an average car transmission (calculated) [4]. | – | [4] |
| Assemble and fill | Gears, shafts, bearings, synchronisers or clutches and planetary sets are built into the casing, then filled with oil and tested. | – | – |
as of 2026-11-17
Technologies used to make it
The technologies used to make it, at which step
Made with- CNC Numerical control machining Cutting gear teeth and machining shafts and casings Tooth cutting and finishing are done on numerically controlled machines.
as of 2026-11-17
Technologies inside it
The technologies inside the product, with how much of each per unit
Embodies- Ger Gear train Meshing toothed wheels set the ratios.
- MPT Mechanical power transmission The wider family of drives that carry mechanical power.
as of 2026-11-17
Sources
- Update of Vehicle Material Compositions in the GREET Model (Kelly and Winjobi) Argonne National Laboratory, 2020, Appendix Table A-1
- Life Cycle Assessment of a novel functionally integrated e-axle compared with powertrains for electric and conventional passenger cars (Koroma, Costa, Puricelli and Messagie, Science of the Total Environment 904, 166860) Elsevier, 2023, Tables 1, 3 and 4
- Transmission fluid, grade and volume (Volvo XC60, 2014 model) Volvo Car Australia support, 2014
- Gearbox Life Cycle Assessment (Su and Ren, 14th IFToMM World Congress) IFToMM, 2015
- Smart alloying eliminates manufacturing steps in automotive gears (Lothman) Gear Technology, 2026
- Mineral Commodity Summaries 2026: Molybdenum US Geological Survey, 2026