Waste-heat power (steam Rankine): Overview
What it does
The job the technology does for people, in a short paragraph
Waste heat to power uses a steam cycle to make electricity from hot exhaust that would otherwise be lost. A boiler takes heat from a kiln, furnace or engine exhaust, and the steam drives a turbine [2]. Auguste Rateau was building turbines for low-pressure exhaust steam by 1902 [1]. Kawasaki alone has had orders for more than 270 such units for cement plants [3]. A US study found 8,840 MW of potential at 2,946 industrial sites [2].
as of 2026-11-12
How it works
The working principle in plain words, step by step
The plant follows the steam cycle that Rankine described in 1859 [4][5]. Water is pumped to high pressure and enters a heat recovery boiler [2]. The waste heat turns it to steam, which expands through a turbine that drives a generator [2]. The spent steam goes to a condenser, where it turns back to water, and the water returns to the pump [2]. A steam cycle needs high-grade heat to make superheated steam, so it suits hot exhausts such as kiln and furnace gas [2]. Steam turbines in this service range from 50 kW to several hundred megawatts [2]. Because it is a heat engine, its efficiency is only a fraction of the ideal Carnot figure: typically 30% to 50% of it [2][6].
as of 2026-11-12
Key figures
The handful of numbers that size it up, each with its unit, year and source
| Figure | Value | Unit | Year | Source |
|---|---|---|---|---|
| Waste-heat-to-power technical potential in US industry, from 2,946 sites | 8840 | MW | 2016 | [2] |
| Rankine cycle efficiency (steam or organic) as a share of Carnot efficiency, top of the 30 to 50% range | 50 | % of Carnot | 2021 | [2] |
| Capital cost of steam Rankine cycle systems, top of the range from $1,200 | 3000 | USD per kW | 2021 | [2] |
| Cement-plant waste heat recovery units ordered from Kawasaki, more than | 270 | units | – | [3] |
| Total power output of installed Kawasaki waste heat recovery units, about | 2880 | MW | – | [3] |
| Share of a cement factory's electricity that waste heat recovery can supply, top of the 20 to 40% estimate | 40 | % | – | [3] |
as of 2026-11-12. The 8,840 MW covers waste streams above 450°F and comes from a DOE report published in 2016 [2]. The 30 to 50% and the capital cost range are from the April 2021 fact sheet, which gives them no data year [2]. The Kawasaki figures are one maker's own order record, in an undated article [3].
Where it is used
The main places and products the technology is found in
- Cement plants, where waste heat from the kiln drives a steam turbine [3]
- Petroleum refining and iron and steel, which have the greatest potential in the US study, followed by stone, clay and glass [2]
- Steel works, where Rateau's exhaust steam accumulators proved valuable [1]
- Incinerators, flared gas and chemical processes, also listed as heat sources [2]
as of 2026-11-12
Scale today
How much of it there is now: units in use, made each year and who uses it
- Installed
- About 2,880 MW from one maker's cement plant units
- Users
- Cement, steel and refining plants
- Unit
- MW
- Note
- No world total was found. The Kawasaki figure counts only its own units, with orders for more than 270 units in Japan and 14 other countries [3].
as of 2026-11-12
Sources
- Auguste Rateau Grace's Guide to British Industrial History
- Waste Heat to Power, CHP Technology Fact Sheet Series (DOE/EE-2347) US Department of Energy, 2021
- Recovering heat across the globe World Cement (article by Kazuki Ao, Kawasaki Heavy Industries)
- William John Macquorn Rankine Encyclopaedia Britannica
- Manual of the Steam Engine and other Prime Movers Encyclopaedia Britannica
- June 12, 1824: Sadi Carnot Publishes Treatise on Heat Engines APS News, American Physical Society, 2009