Electric generator: Bill of materials
About these figures
Which unit, study and year the composition figures describe, and how they vary
Each variant is a different machine on its own basis. Synchronous: one ABB GBA 1120 generator of 31,000 kW, 63,780 kg (sum of its declaration's table) [1]. Permanent magnet: one 15 MW direct-drive wind generator of 185.283 t, of which the 100.63 t structure is not counted for lack of a material [3]. Diesel set: one Caterpillar DE500 GC of 2,924 kg; no published material breakdown was found, so only the engine is linked [5][6]. Insulation (1,094 kg), resin (281 kg) and paint (63 kg) of the ABB machine have no node and are not counted.
as of 2026-11-13
Components
The products inside one unit, with quantity, mass share and cost share
Variant 1 Permanent magnet (direct drive, 15 MW)| Material | Role | Amount in one unit | Share of the unit's mass |
|---|---|---|---|
| Permanent magnet | Component | 10,904 kg | 5.9% |
| Permanent magnets in one 15 MW direct-drive wind generator of 185.283 t; the medium-speed layout holds 0.961 t [3]. Mass share calculated. | |||
| Material | Role | Amount in one unit | Share of the unit's mass |
|---|---|---|---|
| Internal combustion engine | Component | 1 engine | – |
| A C13 in-line six-cylinder diesel engine drives the set [5]. The engine's share of this set's mass is not published; in a different set (a 15 litre engine, studied in a 2016 thesis) the engine was 37.8% and the alternator 44.7% of the mass [7]. | |||
as of 2026-11-13. The synchronous variant has no component that is a product node.
Direct materials
The commodities and chemicals in one unit as bought, with amount, mass share, cost share and recycled content
Variant 1 Synchronous (ABB GBA 1120, 31 MW)| Material | Role | Amount in one unit | Share of the unit's mass |
|---|---|---|---|
| St Steel | Structural | 53,926 kg | 84.6% |
| Electro steel 21,496 kg, normal rolled steel 26,644 kg, special steel 4,524 kg and cast iron 1,262 kg, summed (calculated; cast iron counted under steel); total 63,780 kg for the 31 MW machine (calculated sum of the table) [1]. | |||
| Cu Copper | Functional | 5184 kg | 8.1% |
| Winding copper of the 31 MW machine [1]. | |||
| Tm Timber | Consumable | 3040 kg | 4.8% |
| Wooden boxes and planks used to pack the machine [1]. | |||
| Al Aluminium | Functional | 192 kg | 0.3% |
| Aluminium in the 31 MW machine [1]. | |||
| Material | Role | Amount in one unit | Share of the unit's mass |
|---|---|---|---|
| St Steel | Structural | 53,282 kg | 28.8% |
| Stator core 38,785 kg plus rotor core 14,497 kg (calculated sum) of the 185,283 kg generator [3]; the study gives masses only, and the cores are counted as steel on the assumption that they are steel laminations. The 100,630 kg 'approximated structure' is not counted, because the study does not name its material. | |||
| Cu Copper | Functional | 20,466 kg | 11% |
| Armature copper of a 15 MW direct-drive generator (20.466 t); the medium-speed layout has 5.842 t [3]. Mass share calculated. | |||
as of 2026-11-13. The diesel set has no material rows: no source found gives a material breakdown of a generating set, and the draft's split (an engine share from a different set, the rest in the proportions of a 31 MW ABB machine) was an estimate of the writer's, not a published figure.
How it is put together
The main steps from parts and materials to the finished unit
| Step | What happens | Source |
|---|---|---|
| Cut and stack the core | Electrical steel sheets are cut and stacked into the stator and rotor cores. | – |
| Wind the stator | Copper conductors are placed in the stator slots and insulated. | – |
| Build the rotor | A synchronous rotor gets a wound field winding; a permanent magnet rotor gets magnets fixed to the core. | – |
| Impregnate and cure | Windings are soaked in impregnation resin and cured; the ABB 31 MW machine uses 281 kg of resin. | [1] |
| Assemble frame and cooling | Rotor, stator, bearings and the cooling system (air, hydrogen or water) are fitted into the frame. | – |
| Test and couple | The machine is run to check efficiency and heating, then coupled to its turbine or engine; a diesel set is built on one frame with the engine. | [5] |
as of 2026-11-13
Technologies inside it
The technologies inside the product, with how much of each per unit
Embodies- Gen Generators and alternators 1 generator The electromagnetic machine itself.
- Nd Neodymium magnets 10,904 kg Permanent magnet (direct drive, 15 MW) NdFeB magnets in the rotor of a 15 MW direct-drive generator; 0.961 t in the medium-speed layout [3].
- ICE Internal combustion engines and gensets 1 engine Diesel generating set (Caterpillar DE500 GC, 500 kVA) A C13 four-cycle diesel engine [5].
as of 2026-11-13
Sources
- Environmental Product Declaration for AC-machine type GBA 1120 ABB (Generators and motors, EPD under the 2000 product-specific requirements for rotating electrical machines)
- A prospective life cycle assessment of drivetrain technologies in offshore wind (Dighe, Bansal, Jansen, Breuer and van der Mijle Meijer), Journal of Physics: Conference Series 3131, 012043 IOP Publishing, EERA DeepWind Conference, 2025, Table 2
- DE500 GC (50 Hz) | 500 kVA Diesel Generator Caterpillar, 2026
- Modèle Secours Performance DE500 GC 50 Hz (standby performance data sheet, in French) Caterpillar, hosted by HelloPro
- A Life Cycle Assessment of a Diesel Generator Set (Kelly Benton, graduate thesis) Montana Tech of the University of Montana (Master of Science thesis), 2016