Material Insights · Understanding the Material World

Electric motor: Bill of materials

About these figures

Which unit, study and year the composition figures describe, and how they vary

Each variant is a different motor. Induction figures are for one 110 kW, four-pole cast iron industrial motor of class IE2 (707 kg) in a 2018 study; at IE4 it has 10% more electrical sheet and copper, up to 744 kg [3]. Permanent magnet figures are for one 100 kW car traction motor of 44.9 kg [5][6]. Impregnation resin (5 kg), packaging and drive electronics have no node and are not counted.

as of 2026-11-13

Components

The products inside one unit, with quantity, mass share and cost share

Variant Permanent magnet motor (100 kW car traction, 44.9 kg)
MaterialRoleAmount in one unitShare of the unit's mass
Permanent magnetComponent1.26 kg2.8%
Neodymium-dysprosium-iron-boron magnets in a 100 kW peak car traction motor of 44.9 kg; 26% of the magnet is neodymium and 4% dysprosium [6]. Basis: one traction motor, not the 110 kW industrial motor.

as of 2026-11-13

Direct materials

The commodities and chemicals in one unit as bought, with amount, mass share, cost share and recycled content

Variant 1 Induction motor (110 kW industrial, IE2, 2018 study)
MaterialRoleAmount in one unitShare of the unit's mass
St SteelStructural606 kg85.7%
Ferrous metal of a 110 kW, four-pole cast iron motor of class IE2 (707 kg without packaging): electrical sheets 271 kg, cast iron 271 kg and other steel 64 kg (calculated sum); cast iron has no node of its own [3].
Cu CopperFunctional69 kg9.8%
Winding wire of the same 110 kW motor [3]; mass share calculated from 707 kg.
Al AluminiumFunctional19 kg2.7%
Rotor cage of the same 110 kW motor [3]; mass share calculated from 707 kg.
Variant 2 Permanent magnet motor (100 kW car traction, 44.9 kg)
MaterialRoleAmount in one unitShare of the unit's mass
St SteelStructural20.2 to 23.3 kga range, no single figure –
Electrical steel sheets in the stator and rotor of the 44.9 kg traction motor [6]. No mass is given for this motor; low and high are 45 to 52% of 44.9 kg, the range a 2026 study gives across its four traction machines (calculated) [5].
Al AluminiumStructural13.5 to 16.2 kga range, no single figure –
Aluminium housing parts [6]. Low and high are 30 to 36% of 44.9 kg, the range the 2026 study gives across its four traction machines (calculated) [5].
Cu CopperFunctionalNot given –
Enamelled copper wire windings of the 44.9 kg traction motor; no source gives the mass [6].

as of 2026-11-13

How it is put together

The main steps from parts and materials to the finished unit

StepWhat happens
Cut and stack the coreElectrical steel sheets are punched into thin laminations and stacked to form the stator and rotor cores; a large part of the sheet is lost as scrap.
Wind the statorCopper wire is wound or inserted into the stator slots and varnished or resin-impregnated.
Make the rotorInduction rotors get an aluminium or copper cage, usually die cast; permanent magnet rotors have magnets inserted or bonded into slots.
Cast the frameThe frame and end shields are cast in iron or aluminium and machined.
Assemble and testShaft, bearings, fan and housing are fitted, and the motor is tested for efficiency and temperature rise.

as of 2026-11-13

Technologies inside it

The technologies inside the product, with how much of each per unit

Embodies

as of 2026-11-13

Sources

  1. Comparative life cycle assessment of electric motors with different efficiency classes: a deep dive into the trade-offs between the life cycle stages in ecodesign context (Auer and Meincke, International Journal of Life Cycle Assessment 23(8), 1590-1608) Springer, 2018, Tables 2 and 3
  2. Life cycle assessment of electric traction induction machines (Hsieh, Nordelof, Grunditz and Thiringer, International Journal of Life Cycle Assessment 31, 16) Springer, 2026, Tables 1 to 3 and sections 4.4 to 4.6
  3. Allocating the environmental burdens in coproduction of rare earth elements for EV magnets (Nordelof and Bongards, EVS38) Chalmers University of Technology, 2025, Section 4.3