Material Insights · Understanding the Material World

Integrated circuit (chip): Bill of materials

About these figures

Which unit, study and year the composition figures describe, and how they vary

The amounts come from one 2002 study of one chip type: a 32 MB DRAM chip on a 200 mm wafer, 2.0 g packaged, with a 1.2 cm2 die, a 1.2 g copper lead frame and 0.7 g of epoxy [9]. Modern processors, analogue and compound chips differ, and no source opened gives their composition, so gold bond wire and gallium are named but carry no amount. Silicon wafers, packages and analogue chips are not yet nodes.

as of 2026-11-13

Direct materials

The commodities and chemicals in one unit as bought, with amount, mass share, cost share and recycled content

MaterialRoleAmount in one unitShare of the unit's mass
N2 Nitrogen gasConsumable700 g–
Elemental gases, mainly nitrogen, used in fabrication per 2 g DRAM chip in one 2002 study of one chip type [9]; the study also counts 72 g of chemicals per chip, not split by chemical.
H₂O WaterConsumable32 kg–
Water used in fabrication per 2 g DRAM chip in one 2002 study of one chip type [9].
Cu CopperStructural1.2 g60%
Copper lead frame of the 2 g DRAM chip in one 2002 study of one chip type; mass share calculated (1.2 g of 2.0 g) [9].
EPX Epoxy resinsStructural0.7 g35%
Epoxy package of the 2 g DRAM chip in one 2002 study of one chip type; mass share calculated (0.7 g of 2.0 g) [9].
Si SiliconStructural0.256 g–
Wafer silicon input per DRAM chip in one 2002 study of one chip type (calculated: 1.6 cm2 of wafer x 0.16 g per cm2), including the 25% lost to yield; the die in the package weighs less [9].

Indicative · as of 2026-11-13. The only per-chip table found is one 2002 study of one chip type, a 32 MB DRAM chip of about 2000 [9]. Processor, analogue and compound chips will differ. Gold bond wire and gallium are left out because no source opened gives an amount per chip.

How it is put together

The main steps from parts and materials to the finished unit

StepWhat happensTechnologySource
Grow and slice the siliconA crystal of very pure silicon is grown and sliced into polished wafers.Czochralski crystal growth–
Print the circuit layersLight through a patterned mask marks each layer on a resist coating; EUV light is used for the finest layers.Planar process and photolithography[35]
Etch, coat and dopeEtching, thin-film deposition and doping repeat for up to 1,500 steps to build transistors and wiring.Atomic layer deposition[38]
Test and cut the waferWorking dies are found by testing the wafer, then the wafer is cut up.– –
PackageA good die is fixed to a copper lead frame and sealed in epoxy.– [9]
Final test and shipPackaged chips are tested again and sent to board makers.– –

as of 2026-11-13

Technologies used to make it

The technologies used to make it, at which step

Made with 4

as of 2026-11-13

Technologies inside it

The technologies inside the product, with how much of each per unit

Embodies
  • Tsr Transistor Every chip is built from transistors; no source opened gives the number for the class.
  • MOS MOSFET Most chips are built from metal-oxide-silicon transistors.

as of 2026-11-13

Sources

  1. The 1.7 Kilogram Microchip: Energy and Material Use in the Production of Semiconductor Devices Williams, Ayres and Heller, Environmental Science & Technology (author copy on freedomsolarpower.com), 2002
  2. ASML Annual Report 2025: strategic report ASML Holding N.V., pp. 8, 17, 22
  3. 5 things you should know about High NA EUV lithography ASML, 25 January 2024, 2024
  4. Semiconductor manufacturing footprint: sustainability as roadmap metric Marie Garcia Bardon, imec (presentation slides, September 2020), 2020