Power semiconductor module: Bill of materials
About these figures
Which unit, study and year the composition figures describe, and how they vary
Shares are from Infineon's material sheets for its Easy3 B-Series with SiC (76 g, 2021) [3] and Easy3B IGBT7 (82 g, 2023) [5]. By mass these modules are mostly plastic housing (PBT 34% and glass fibre 15% in the SiC sheet), copper, ceramic and gel; the SiC chips are 0.21% [3]. Chips, ceramic board and baseplate are named in new_products. The sheets name no part numbers or voltage; a 1200 V Infineon EasyPACK CoolSiC module weighs 78 g [38].
as of 2026-11-17
Direct materials
The commodities and chemicals in one unit as bought, with amount, mass share, cost share and recycled content
Variant 1 SiC MOSFET| Material | Role | Amount in one unit | Share of the unit's mass |
|---|---|---|---|
| Cu Copper | Functional | 0.02 kg | 26.85% |
| Calculated: 26.85% (23.69 + 3.16) of the 76 g Easy3 B SiC module, about 20.4 g [3]. Baseplate, board tracks and terminals; the split between them is not given. The 41 g Easy2 B SiC module declares 23.3% (20.2 + 3.1) [4]. | |||
| Sil Silicones | Functional | 0.009 kg | 11.85% |
| Calculated: 11.85% of 76 g, about 9.0 g of silicone gel that fills the case [3]. | |||
| Sn Tin | Functional | 0.001 kg | 1.05% |
| Calculated: 1.05% of 76 g, about 0.80 g, mostly solder [3]. | |||
| Ag Silver | Functional | 0.001 kg | 0.66% |
| Calculated: 0.66% of 76 g, about 0.50 g [3]. | |||
| Al Aluminium | Functional | 0 kg | 0.53% |
| Calculated: 0.53% of 76 g, about 0.40 g [3]. | |||
| Material | Role | Amount in one unit | Share of the unit's mass |
|---|---|---|---|
| Cu Copper | Functional | 0.023 kg | 28.3% |
| Calculated: 28.3% (24.2 + 4.1) of 82 g, about 23.2 g [5]. | |||
| Sil Silicones | Functional | 0.011 kg | 13.9% |
| Calculated: 13.9% of 82 g, about 11.4 g of silicone rubber [5]. | |||
| Sn Tin | Functional | 0.002 kg | 2.1% |
| Calculated: 2.1% (0.2 + 1.9) of 82 g, about 1.7 g [5]. No silver is declared. | |||
| Si Silicon | Functional | 0 kg | 0.3% |
| Calculated: 0.3% of the 82 g Easy3B IGBT7 module, about 0.25 g, the chips [5]. | |||
as of 2026-11-17. Amounts are mass shares of makers' own declarations applied to the declared module mass; the sheets are for series of modules, not for one named 1,200 V part.
Cost breakdown
The share of the unit's cost in each component or stage
| Part | Share of cost | Variant | Year | Source |
|---|---|---|---|---|
| SiC chips (MOSFETs and Schottky diodes), midpoint of 65 to 75% of materials cost (calculated); study is of modules for medium-voltage motor drives | 70% | SiC MOSFET | 2017 | [33] |
| Packaging materials (die attach, ceramic boards, baseplates), about 30% of total power module cost | 30% | – | 2023 | [37] |
as of 2026-11-17
How it is put together
The main steps from parts and materials to the finished unit
| Step | What happens | Technology | Source |
|---|---|---|---|
| Make the chips | Wafers of silicon or silicon carbide are processed into power chips in a fab and cut up. The inventory study leaves wafer making outside its boundary [2]. | Planar process and photolithography | [2] |
| Solder the chips to the ceramic board | Chip soldering is the first of two soldering steps [2]. Silver or copper sintering is replacing solder for silicon carbide chips [7]. | – | [2][7] |
| Solder the board to the baseplate | System soldering joins the ceramic board to the copper baseplate [2]. | – | [2] |
| Wire bond | Wires join the upper side of the chips to the circuit tracks [2]. | – | [2] |
| Fit the frame | A moulded plastic frame with terminals is attached to the baseplate [2]. | Injection moulding | [2] |
| Fill with gel and cure | Silicone gel is poured over the chips and cured with UV light [2]. | – | [2] |
| Glue on the lid | A silicone adhesive seals the lid to the frame [2]. | – | [2] |
as of 2026-11-17
Technologies used to make it
The technologies used to make it, at which step
Made with- Lit Planar process and photolithography Pattern the power chips on wafers Chips are made in a fab; no source opened gives the process steps for power chips.
- IM Injection moulding Mould the plastic frame The study says the frame is moulded [2]; injection moulding is the usual route for such plastic but the study does not say so.
as of 2026-11-17
Technologies inside it
The technologies inside the product, with how much of each per unit
Embodies- MOS MOSFET 2 SiC MOSFET chips per 1-in-1 module (Tesla Model 3 inverter, 2018) Each module in the Model 3 inverter held two SiC MOSFETs [14].
- Tsr Transistor The IGBT variant switches with insulated gate bipolar transistors; the twin technology page tells the transistor story.
as of 2026-11-17
Sources
- A scalable life cycle inventory of an automotive power electronic inverter unit, part II: manufacturing processes The International Journal of Life Cycle Assessment (Springer), 2019
- Material Content Data Sheet: Umbrella Spec Easy3 B-Series with SiC Infineon Technologies, 2021
- Material Content Data Sheet: Umbrella Spec Easy2 B-Series with only SiC + TIM Infineon Technologies, 2023
- Material Content Data Sheet: Umbrella Spec Easy3B IGBT7 Infineon Technologies, 2023
- Critical Materials for Power Module Packaging: Market Outlook, Supply Chain Risk & Technology Trends 2026-2036 (report sales page) Future Markets Inc, 2026
- Complete Teardown Report of STMicroelectronics's Inverter with SiC Power Module for the Tesla Model 3 Research and Markets via GlobeNewswire, 2018
- A Manufacturing Cost and Supply Chain Analysis of SiC Power Electronics Applicable to Medium-Voltage Motor Drives (NREL/TP-6A20-67694; Horowitz, Remo and Reese) National Renewable Energy Laboratory, 2017
- xEVs drive surge in power module packaging market Yole Group
- F3L3MR12W3M1H_H11 datasheet: EasyPACK module with CoolSiC Trench MOSFET and PressFIT / NTC (revision 1.20) Infineon Technologies, 2025