Rolling bearing: Bill of materials
About these figures
Which unit, study and year the composition figures describe, and how they vary
The materials describe a deep groove ball bearing of the reference 6010 type: 100Cr6 rings and balls, a cage of pressed steel (as in the 6010C4), brass or polyamide, grease, and in sealed types acrylonitrile-butadiene rubber (NBR) seals with a steel insert. Large pitch bearings have 42CrMo4-type rings and 100Cr6 rolling bodies. Hybrid bearings use silicon nitride balls. The mass split between parts was not found. NBR, a plain bearing and a bearing steel bar are not yet nodes. [8][14][17][46][15]
as of 2026-11-15
Direct materials
The commodities and chemicals in one unit as bought, with amount, mass share, cost share and recycled content
Variant 1 Ball| Material | Role | Amount in one unit | Share of the unit's mass | Recycled content |
|---|---|---|---|---|
| St Steel | Structural | up to 0.261 kga range, no single figure | – | 51% |
| Rings are 100Cr6 bearing steel, about 1% carbon and 1.5% chromium [14]; the 6010C4 reference also has a pressed steel cage [8]. The upper figure is the whole mass of the 6010 [8]; the split between steel, seals and grease was not found. 51% is SKF's estimated group share of bearing steel from scrap-based sources in 2025 [3]. | ||||
| Cr Chromium | Functional | Not given | – | – |
| About 1.5% of the ring steel by weight [14]; this chromium is inside the steel above, not extra mass. | ||||
| PA Nylon (PA6, PA66) | Structural | Not given | – | – |
| Polyamide 66 or 46 cages are one option [14]; a cage is typically under 10% of a rolling bearing's weight [16]. The 6010C4 reference has a pressed steel cage, so no polyamide [8]. | ||||
| Cu Copper | Functional | Not given | – | – |
| Machined cages are made of brass (copper and zinc) or sometimes steel or light alloy [14]. The share of bearings with brass cages was not found. | ||||
| Zn Zinc | Functional | Not given | – | – |
| In brass cages, as for copper [14]. | ||||
| Lub Lubricant additives | Consumable | Not given | – | – |
| Grease, filled at the factory; in one SKF wheel bearing study grease was under 1% of the carbon footprint [36]. | ||||
| Material | Role | Amount in one unit | Share of the unit's mass |
|---|---|---|---|
| St Steel | Structural | Not given | – |
| Rings of large pitch bearings are usually 42CrMo4-type steel, with 100Cr6 rolling bodies [46]. No mass was found. | |||
as of 2026-11-15
How it is put together
The main steps from parts and materials to the finished unit
| Step | What happens | Technology | Source |
|---|---|---|---|
| Shape the rings | Rings start as tube stock; the blanks may be forged or turned to shape. | Lathe | [19][20] |
| Form the balls | Wire slugs are cold-headed to a near-round shape, deburred and soft ground. | – | [19] |
| Harden | Rings are heated to about 850 C (1565 F in the source) for 15 to 20 minutes, quenched in oil and tempered; balls are hardened in a similar way. | – | [19] |
| Grind and finish | Faces, bores and races are ground and the races honed; balls are finish ground and lapped to final size and roundness. | – | [19] |
| Assemble | Balls, cage and any seals or shields are fitted into the rings. | – | [20] |
| Lubricate | Bearings are lubricated with grease or oil; bearings sealed or shielded on both sides are filled with grease at the factory. | – | [20][14] |
as of 2026-11-15
Technologies used to make it
The technologies used to make it, at which step
Made with- Lth Lathe Turning ring blanks to shape Blanks are forged or turned before grinding [20]; the share made this way was not found.
as of 2026-11-15
Sources
- SKF Annual Report 2025 AB SKF, 2026
- NSK 6010C4 deep groove ball bearing data page NSK Ltd, 2026
- Components and materials of SKF bearings Coolen Bearings (reproducing SKF technical text)
- A guide to material selection for rolling bearings Bearing News, 2013
- Sustainable thinking from scratch Schaeffler tomorrow
- Longer life and lower energy use with SKF Sealed Energy Efficient deep groove ball bearings SKF Evolution, 2014
- How ball bearings are manufactured GlobalSpec Insights
- Bearing manufacturing process: a comprehensive guide to precision and innovation NBC Bearings, 2024
- Sustainability and grease lubrication in rolling bearings Berens and Lugt, Tribology and Lubrication Technology (STLE), 2023
- Life Cycle Assessment of Large Structure Mechanical Endurance Tests: Identifying Hotspots and Reduction Potentials (MA thesis) Hamburg University of Applied Sciences / Fraunhofer IWES, 2024