Fluids: pressure, flow, lift and drag: Pressure and buoyancy: what fluids do when they stand still
All courses / Understanding Engineering / Module 5: Fluids: pressure, flow, lift and drag Part 1 of 5Pressure and buoyancy: what fluids do when they stand still
Your ears ache at the bottom of a deep swimming pool, a steel ship floats, and a brake pedal that moves a few centimetres stops a car of well over a tonne. All three come from one idea, pressure in a fluid at rest. This part defines pressure, shows how it grows with depth, how a sealed liquid passes it on, and how it holds up a ship.
1.1 Pressure is force per area, and in still water it grows by about one atmosphere for every ten metres of depth
Press your thumb on the flat head of a drawing pin, then on its point. The force is the same, but the point hurts because the same push is squeezed onto a tiny area. Pressure is force divided by area. Its SI unit is the pascal, one newton on one square metre. A pascal is very small, so engineers use kilopascals (kPa), megapascals (MPa) and the bar, which is 100 kPa and close to the pressure of the atmosphere.
In a fluid at rest, pressure is the weight of the fluid overhead, spread over the area beneath it. Imagine a column of water h metres tall standing on a base of area A. Its volume is A x h, its mass is density x A x h, and its weight is that mass x g. Divide the weight by A and the area cancels: pressure = density x g x h. With water at 1,000 kg/m3, one metre adds 1,000 x 9.8 x 1, about 10 kPa. A diver at 10 m carries about one extra atmosphere.
At scale this matters: a gate 50 m down in a dam carries about 490 kPa, nearly five atmospheres, on every square metre.
Most gauges show gauge pressure, the excess over the atmosphere, since air presses on both faces of most walls and its share cancels. The table works four cases.
The same arithmetic limits a farmer's borewell. A pump on the surface cannot pull water up a pipe; it can only lower the pressure at the top, and then the atmosphere pushes the water up. A perfect vacuum is balanced by about 10.3 m of water, and practical suction lifts stop near 7 m. Water lying 30 m down therefore needs a submersible pump sitting in the water and pushing it up. The trade-off is plain: the submersible removes the lift limit, but any repair means hauling the whole pump and its pipe out of the bore.
| Case | Working | Result |
|---|---|---|
| Swimmer's ear at the bottom of a 3 m pool | 1,000 kg/m3 x 9.8 m/s2 x 3 m = 29,400 Pa | about 29 kPa, 0.3 bar above the atmosphere |
| Dam gate 50 m below the reservoir surface | 1,000 x 9.8 x 50 = 490,000 Pa | about 490 kPa, nearly 5 bar |
| Submersible pump hung 30 m below the water surface in a borewell: pressure at its inlet | 1,000 x 9.8 x 30 | about 294 kPa, nearly 3 bar |
| Largest suction lift in theory | 101,300 Pa / (1,000 x 9.8) | 10.3 m, about 7 m in practice |
All results calculated, with g = 9.8 m/s2 and fresh water at 1,000 kg/m3. Check: a car tyre at about 2 bar holds roughly the pressure of 20 m of water, and the 10.3 m limit is simply one standard atmosphere (101,300 Pa) expressed as a height of water.
Source: Bloomfield, How Things Work (Wiley, 2015), ch. 5, 'Fluids', section 5.2 (hydrostatics and water distribution)- Bloomfield, How Things Work (Wiley, 2015) · ch. 5, 'Fluids', sections 5.1 and 5.2 (pressure, density, hydrostatics)
- Feynman, Leighton and Sands, The Feynman Lectures on Physics, vol. II (Caltech online edition) · further reading: ch. 40, 'The Flow of Dry Water', https://www.feynmanlectures.caltech.edu/II_40.html
1.2 A sealed liquid passes pressure on everywhere, so a small push on a small piston becomes a big push on a big one
A liquid is almost impossible to squeeze. If you trap it in a closed pipe and push on one end, the pressure rises by the same amount at every point inside, and the walls feel it equally. This is the idea behind hydraulics. Put a small piston at one end of a sealed oil-filled line and a larger piston at the other. The pressure is the same on both, so the force on each piston is pressure x its own area. A piston with ten times the area delivers ten times the force.
This is not free. The oil that the small piston pushes out is the oil that moves the large piston, so the small piston must travel ten times as far as the large one. Force is gained and distance is lost, and work in equals work out less friction. It is the same trade as a lever in the module Force, motion and energy, carried through a pipe.
Unlike a lever, the pipe can bend round corners, so one pedal at the front can reach brakes at all four wheels. The design trade-off is leakage and air. Oil can be pushed hard, but a leak loses the pressure, and a bubble of air compresses where oil would not, so a spongy pedal means air in the line and needs bleeding. Brake fluid also absorbs water over the years, and that water can boil in a hot brake into compressible vapour, so the fluid is changed on a schedule.
| Step | Working | Result |
|---|---|---|
| Pedal force and lever (assumed) | 150 N x lever ratio 4 | 600 N on the master piston |
| Master piston, bore 20 mm (assumed) | area = 3.14 x 0.01 x 0.01 = 314 mm2 | 3.14 x 10^-4 m2 |
| Line pressure | 600 N / 0.000314 m2 | 1.9 MPa, about 19 bar |
| Caliper piston, bore 40 mm (assumed) | area = 3.14 x 0.02 x 0.02 = 1,257 mm2 = 0.001257 m2 | area ratio 4 |
| Clamp force from one piston | 1,900,000 Pa x 0.001257 m2 | about 2.4 kN, four times the master force |
| Travel trade | caliper piston moves 1/4 as far as the master piston, which moves 1/4 as far as the pedal | pedal moves about 16 mm for each 1 mm of caliper piston travel |
All results calculated from assumed round figures. Check: real cars add a vacuum or electric booster that multiplies the driver's force several times, so line pressures in a hard stop are several times this unboosted 19 bar, and real bore sizes vary from car to car.
Source: Bloomfield, How Things Work (Wiley, 2015), ch. 5, 'Fluids', section 5.2 (Pascal's principle and hydraulics)- Bloomfield, How Things Work (Wiley, 2015) · ch. 5, 'Fluids', section 5.2 (Pascal's principle, hydraulics)
1.3 Buoyancy is the weight of the fluid pushed aside, so a steel ship floats if its shape displaces more water than the steel weighs
Push an empty plastic bottle under water and feel it shove back. The water pressure is higher on the lower face than on the upper, and the difference adds up to an upward force. That force is the buoyant force, and it equals the weight of the fluid the object pushes aside. A body floats when it can displace its own weight of fluid before it is fully under. It sinks if even fully under it displaces less than its weight.
Steel is almost eight times denser than water, yet ships of steel float, because the hull is a hollow shape. Most of its volume is air, so the average density of the whole vessel, steel and air together, is below that of water. A solid steel block of the same mass would sink straight to the bottom. Naval architects therefore work with displacement: the mass of water the hull pushes aside when floating at a given draught, which equals the mass of the ship and its cargo. A Cargo ship loaded with Shipping container boxes sits lower in the water, because each extra tonne displaces one more tonne of sea water.
Sea water is about 2.5 per cent denser than fresh water, so a ship rides slightly lower in a river port than it does at sea. The trade-off is cargo against safety: every extra tonne eats into the reserve of buoyancy above the waterline that keeps a ship up in a heavy sea. The table works through a barge.
| Step | Working | Result |
|---|---|---|
| Underwater volume | assumed length 100 m x width 20 m x draught 6 m x assumed shape factor 0.8 (hull is not a box) | 9,600 m3 |
| Displacement in sea water (1.025 t/m3) | 9,600 x 1.025 | about 9,840 tonnes: ship plus cargo |
| Area at the waterline | 100 x 20 x assumed waterplane factor 0.85 | about 1,700 m2 |
| Cargo that sinks it 1 cm deeper | 1,700 m2 x 0.01 m x 1.025 t/m3 | about 17 tonnes per centimetre |
| In fresh river water (1.000 t/m3) | same weight, so volume needed = 9,840 m3, extra volume = 240 m3; 240 m3 / 1,700 m2 | about 14 cm deeper draught |
| Tonnes the same barge can load at 7 m draught | 6 m to 7 m: 100 cm x 17 t per cm (sides taken as upright) | about 1,700 tonnes more |
All results calculated. Check: a real vessel of this size has a deadweight of several thousand tonnes, and port authorities count each centimetre of draught because it is worth tens of tonnes of cargo.
Source: Bloomfield, How Things Work (Wiley, 2015), ch. 5, 'Fluids', section 5.1 (Archimedes' principle and buoyant force)- Bloomfield, How Things Work (Wiley, 2015) · ch. 5, 'Fluids', section 5.1 (Archimedes' principle, buoyant force)
See it in the table
H₂O WaterSt SteelCem CementCheck your understanding
Two tanks hold water to the same depth of 3 m. One is the size of a dustbin, the other the size of a swimming pool. How do the pressures on their floors compare?
Pressure = density x g x depth, and the width of the container drops out. What differs is the total force on the floor, which is pressure x area.A hydraulic press has an output piston of 50 times the area of the input piston. What is true?
The oil volume is conserved, so a large piston moves a small distance. Force gain is paid for by distance loss; work out cannot exceed work in.A laden barge moves from the sea into a river. Its weight is unchanged. What happens to its draught?
The barge must still displace its own weight of water. Fresh water is about 2.5 per cent less dense, so the volume needed is larger and the hull sits lower.