Material Insights · Understanding the Material World

Fluids: pressure, flow, lift and drag: Flow, continuity and Bernoulli: what happens when fluid moves

All courses / Understanding Engineering / Module 5: Fluids: pressure, flow, lift and drag Part 2 of 5

Flow, continuity and Bernoulli: what happens when fluid moves

Once water moves, new questions arise: how much passes each second, how fast it goes in a narrow section, and what happens to its pressure. This part gives three tools that answer them: continuity, Bernoulli's principle and the habit of drawing an imaginary box round a flow and counting what crosses its walls. Each is used on a city water main or a jet.

2.1 Continuity: what flows in must flow out, so flow rate equals area times speed

Press the plunger of a Syringe slowly and the liquid leaves the needle as a fast, thin jet. The barrel may be a hundred times wider in area than the needle's bore, so every millilitre that the plunger pushes along the barrel must race through the needle a hundred times faster. Nothing is added or lost on the way, only squeezed into a smaller cross-section. This is continuity. For a liquid that cannot be squeezed, the volume passing any cross-section each second is the same all along a pipe with no leaks or branches. The volume flow rate Q is the cross-section area A times the average speed v: Q = A x v, in cubic metres per second.

Halve the diameter of a pipe and the area falls to a quarter, so the speed must rise fourfold. Engineers therefore size a pipe by choosing a sensible speed first. For water in pipes the usual range is 1 to 3 m/s. Below that, the pipe is larger than needed and costs more. Above it, friction losses and the risk of water hammer, a pressure surge when a valve shuts quickly, grow.

How many people can one trunk main serve? The answer rests on its bore, the allowed speed and the daily use per person, as the table shows.

The trade-off is cost against running loss. A wider pipe costs more to buy and to lay in a crowded street, but it allows the water to move slowly with less friction, so the pumps need less power for as long as the pipe lasts. Pipe size is therefore a decision about the whole life of the system.

Data Worked estimate 4: how many people can one city water main serve?
StepWorkingResult
Bore 600 mm, area3.14 x 0.3 x 0.30.283 m2
Design speed (assumed)within the usual 1 to 3 m/s; pick 1.5 m/s1.5 m/s
Flow rate0.283 m2 x 1.5 m/s0.42 m3/s, or 424 litres per second
Per day0.424 m3/s x 86,400 sabout 36,600 m3, 36.6 million litres
Supply norm per person per day (a figure of 135 litres is widely used for planning Indian cities)36.6 million / 135about 270,000 people
Doubling the speed to 3 m/sflow doubles, but friction loss per metre rises about fourfold (part 3)not free, so engineers usually lay a wider pipe instead

Check: a metropolitan water treatment plant produces several hundred million litres a day and is fed by several trunk mains of this size, so one main serving a town of a quarter of a million is the right order of magnitude.

Source: Bloomfield, How Things Work (Wiley, 2015), ch. 5, 'Fluids', section 5.2 (steady state flow)
  • Bloomfield, How Things Work (Wiley, 2015) · ch. 5, 'Fluids', section 5.2 (hydrodynamics and steady state flow)

2.2 Bernoulli's principle: along a smooth flow, a rise in speed is paid for by a fall in pressure

Energy conservation, met in Force, motion and energy, applies to moving fluid too. Follow a small parcel of water along a smooth stream path. It has three kinds of energy per unit volume: pressure energy, kinetic energy (half x density x speed squared) and height energy (density x g x height). If friction is negligible, the sum stays the same along the path. This is Bernoulli's principle. In words: pressure + half x density x speed squared + density x g x height = constant.

The most useful consequence is for flow at a fixed height. Where the fluid speeds up, its pressure falls. Pressure is what pushes a parcel forward into a faster region, so a pressure drop is exactly what speeding up needs. Venturi flow meters use this. A pipe narrows to a throat, the speed rises by continuity, the pressure falls, and a gauge measures the pressure difference. From that difference, the speed and so the flow can be found. The carburettor of an older Motorcycle and scooter engine did the same, using a throat of low pressure to draw fuel into the air stream.

Bernoulli holds only where friction is small and the fluid is not squeezed much, so a long pipe needs the friction rules of part 3. Height energy gives a second use. Water leaving a hole in a tank at depth h gains the speed it would reach in free fall from h: speed = square root of (2 x g x h). Rooftop tanks, siphons and dam outlets follow this rule, and the table has numbers.

Data Worked estimate 5: pressure drop in a throat, and the jet from a tank
CaseWorkingResult
Venturi: 100 mm pipe at 2 m/s narrows to a 50 mm throatthroat area is a quarter, so speed = 2 x 48 m/s
Pressure fall at the throathalf x 1,000 x (8 x 8 minus 2 x 2) = 500 x 6030,000 Pa, 30 kPa
Equivalent water height30,000 / (1,000 x 9.8)about 3 m of water
Jet from a hole 3 m below the surface of a rooftop tanksquare root of (2 x 9.8 x 3)7.7 m/s
Pressure at that hole inside the tank (gauge)1,000 x 9.8 x 329 kPa, which all turned into speed

Check: 7.7 m/s is about 28 km/h, a lively jet but not a violent one for a tank on a bungalow roof, and a venturi with a 3 m water-height difference is easily read on a simple gauge. Real jets run 3 to 5 per cent slower because of friction at the hole.

Source: Bloomfield, How Things Work (Wiley, 2015), ch. 5, 'Fluids', section 5.2 (Bernoulli's equation, pressure potential energy)
  • Bloomfield, How Things Work (Wiley, 2015) · ch. 5, 'Fluids', section 5.2 (Bernoulli's equation); ch. 6, 'Fluids and Motion', section 6.1 (speed and pressure in a fluid)

2.3 The control volume: draw a box round the machine and count what crosses its walls

Start with a puzzle. A fire crew opens a nozzle that sends out 10 litres of water a second, which is 10 kg/s, at 30 m/s. How hard does the hose kick back? Rather than trace the water through every bend, look only at what leaves. Each second, 10 kg of water departs at 30 m/s, carrying 10 x 30 = 300 kg m/s of momentum that was not there before. By Newton's second law, met in the module Force, motion and energy, force is momentum gained per second, so the crew must hold back about 300 N, the weight of some 30 kg. That is why firefighters brace.

The trick in that answer has a name. Draw an imaginary closed surface round the thing you care about, here the nozzle, and call the space inside a control volume. Then do bookkeeping at the surface only: mass in and out, momentum in and out, energy in and out. Whatever happens inside, the imbalance at the surface gives the force or power the machine exchanges with its surroundings. For a stream, momentum per second is mass flow x speed, so the thrust on any device equals mass flow x the change in speed across it.

The same box works on an Aeroplane wing or a Helicopter rotor: the downward momentum given to the air each second is the lift. The historian Walter Vincenti traces how this way of thinking became an explicit engineering method: used without a name on single problems from the eighteenth century, drawn together as a method in fluid mechanics by Ludwig Prandtl at Göttingen from the 1910s, generalised in the decade after 1945, notably in Ascher Shapiro's 1953 work at MIT, and common in engineering textbooks from the mid-1950s. The habit to keep: when a flow looks too hard, draw a surface round it and count only what crosses.

Value chain The three balances on a control volume
  • Closed surface drawn round a nozzle, fan or turbine count only what crosses the surface
    • Mass in = mass out gives speed from area (continuity)
    • Momentum out minus momentum in equals the force on the box: thrust or lift
    • Energy in minus energy out equals power supplied, less heat and noise
Source: Vincenti, What Engineers Know and How They Know It (Johns Hopkins University Press, 1990), ch. 4, 'A Theoretical Tool for Design: Control-Volume Analysis' (the balances only; tree drawn for this module)
  • Vincenti, What Engineers Know and How They Know It (Johns Hopkins University Press, 1990) · ch. 4, 'A Theoretical Tool for Design: Control-Volume Analysis'
  • Bloomfield, How Things Work (Wiley, 2015) · ch. 6, 'Fluids and Motion', section 6.3 (momentum in a fluid, thrust)

See it in the table

H₂O Water

Check your understanding

Water flows steadily through a pipe that narrows to half its diameter. What happens to the speed in the narrow part?

Half the diameter means a quarter of the area. For the same flow rate, speed must rise fourfold, since Q = A x v.

In a horizontal pipe with negligible friction, a section where the water speeds up has what pressure compared with the slower section?

Bernoulli's principle: with height and friction ignored, pressure + half x density x speed squared stays constant, so more speed means less pressure.

A box is drawn round a machine. Air enters at rest and leaves at 6 m/s with a mass flow of 2 kg/s. What is the thrust on the machine?

Thrust = mass flow x change in speed = 2 x 6 = 12 N. The inside of the machine does not need to be known.
← Part 1: Pressure and buoyancy: what fluids do when they stand stillMark read · Part 3: Viscosity, turbulence and pipe friction: what moving fluid costs →