Material Insights · Understanding the Material World

Fluids: pressure, flow, lift and drag: Key terms, quiz and sources

All courses / Understanding Engineering / Module 5: Fluids: pressure, flow, lift and drag Wrap-up

Fluids: pressure, flow, lift and drag: review

Key terms

Pressure
Force divided by the area it acts on, measured in pascals; in still water it equals density x g x depth.
Gauge pressure
Pressure above that of the surrounding atmosphere, the figure most gauges show.
Hydraulics
The use of a sealed liquid to pass force from a small piston to a large one, or round corners, at the cost of distance.
Buoyant force
The upward push on a body in a fluid, equal to the weight of the fluid it pushes aside.
Displacement
The mass of water a floating hull pushes aside, equal to the mass of the ship and its load.
Continuity
The rule that a steady flow of liquid has the same volume rate everywhere along a pipe, so flow rate = area x speed.
Bernoulli's principle
In smooth, steady flow without much friction, pressure falls where speed rises, so pressure + half x density x speed squared + density x g x height stays constant.
Control volume
An imaginary box drawn round a machine so that mass, momentum and energy can be counted at its walls without knowing what happens inside.
Viscosity
The internal friction of a fluid, its resistance to layers sliding past each other.
Reynolds number
The ratio of inertial force to viscous force in a flow: density x speed x size / viscosity, with no units.
Laminar and turbulent flow
Smooth layered flow at low Reynolds number, and chaotic eddying flow at high Reynolds number.
Head
Pressure expressed as the height of fluid that would give it, used for pump and pipe calculations.
Affinity laws
Rules for pumps and fans: flow goes with speed, head with speed squared and power with speed cubed.
Drag coefficient
The pure number Cd that sets drag = half x density x Cd x area x speed squared for a given shape.
Boundary layer
The thin layer of fluid next to a surface that is slowed by friction, and whose separation creates a wake.
Lift coefficient
The pure number CL that sets lift = half x density x CL x wing area x speed squared.
Stall
The loss of lift when flow separates from the top of a wing at too high an angle of attack.
Betz limit
The result that no wind turbine can take more than 16/27, about 59 per cent, of the power in the wind.
Advance ratio
The distance a propeller advances in one turn divided by its diameter, used to compare propellers of different sizes.
Dimensionless number
A ratio with no units, such as Reynolds number, Cd or CL, that lets results from a model carry over to the full-size machine.

Try it in the table

  • Open 'Centrifugal water pump'. Find a typical flow and head for a farm or household model, then repeat estimate 7: work out the hydraulic power from 1,000 x 9.8 x flow x head, and the electrical power at 40 per cent overall efficiency.
  • Under 'Wind turbine blade' and 'Wind turbine generating set', find a rotor diameter and rated power. Redo estimate 11 for that machine: swept area, power in the wind at 6, 8 and 10 m/s, and the wind speed at which output reaches the rating.
  • Look at 'Passenger car' and 'Passenger car tyre'. Take a mass, a frontal area and a published drag coefficient for a model you know, and use estimate 8 to find the power to hold 100 km/h and 120 km/h, then the share that is air.
  • Open 'Aeroplane' and 'Helicopter'. Pick a published maximum takeoff mass and wing area for one aeroplane, and use estimate 9 to find the speed at which lift equals weight with a lift coefficient of 2.0. For the helicopter, say how its rotor area compares and why a large disc suits hovering.
  • Open 'Cargo ship' and 'Shipping container'. Take the length and beam of a ship you read about, estimate its waterline area, and work out the tonnes of cargo per centimetre of draught as in estimate 3.
  • Under 'Goods vehicle', estimate the drag area of a truck from its width and height, and compare its air-drag power at 80 km/h with the car in estimate 8. Say what a roof deflector would have to change.

Final quiz

A sluice gate sits 20 m below the still surface of a reservoir. What is the approximate gauge pressure on the gate?

Each metre of water gives about 10 kPa, so 20 m gives about 200 kPa, 2 bar. The other values are slips of factors of ten.

A 400 mm water main carries water at 2 m/s. About what flow rate is that?

Area = 3.14 x 0.2 x 0.2 = 0.126 m2. Flow = 0.126 x 2 = 0.25 m3/s, about 250 litres a second.

Which of these correctly describes Bernoulli's principle?

Energy per unit volume is conserved along a streamline, so more kinetic energy means less pressure energy. The equal transit time story for wings is false.

A flow has a Reynolds number of 500,000. What does this tell you?

A large Re means inertia beats viscosity, so disturbances grow and the flow is turbulent. Re can be quoted for any fluid and any shape.

A car's speed on a motorway rises from 80 to 120 km/h. By about what factor does the power to overcome air drag rise?

Drag goes as speed squared and power as speed cubed: 1.5 x 1.5 x 1.5 = 3.4. Rolling resistance changes little, so total fuel use rises by less than this.

Why does a wing stall at a high angle of attack?

At a large angle the boundary layer cannot follow the surface against the rising pressure and separates, leaving a wide wake and little lift.

A pump is slowed to half speed by an electronic drive. Roughly what happens to its power?

Affinity laws give power proportional to speed cubed, so half speed needs one eighth of the power, though the flow also halves.

Durand and Lesley's propeller tests are an example of which method?

They varied pitch and shape in planned steps in a wind tunnel and reported results as coefficients against advance ratio, a data set designers could use without further tests.
Next module: Heat and thermodynamics: engines, heat pumps and their limits →

Sources for this module

  • Bloomfield, How Things Work (Wiley, 2015) · ch. 5, 'Fluids' (balloons, buoyancy, water distribution, hydraulics, Bernoulli's equation); ch. 6, 'Fluids and Motion' (viscosity, Reynolds number, drag, lift, airplanes)
  • Vincenti, What Engineers Know and How They Know It (Johns Hopkins University Press, 1990) · ch. 4, 'A Theoretical Tool for Design: Control-Volume Analysis'; ch. 5, 'Data for Design: The Air-Propeller Tests of W. F. Durand and E. P. Lesley' (summarised in the author's own words as facts)
  • Feynman, Leighton and Sands, The Feynman Lectures on Physics, vol. II (Caltech online edition) · further reading: ch. 40, 'The Flow of Dry Water', https://www.feynmanlectures.caltech.edu/II_40.html
  • Feynman, Leighton and Sands, The Feynman Lectures on Physics, vol. II (Caltech online edition) · further reading: ch. 41, 'The Flow of Wet Water', https://www.feynmanlectures.caltech.edu/II_41.html
  • VOICE Society (Consumer VOICE), comparative test of BLDC ceiling fans, hosted by the Department of Consumer Affairs, Government of India (March 2023) · BLDC fan power 26.9 to 35.4 W at full speed; air delivery 224 to 234 m3/min; service value 6.7 to 8.2; 75 W conventional example; https://consumeraffairs.nic.in/sites/default/files/file-uploads/ctocpas/BLDC_Ceiling_Fans_Choosing_Efficiency.pdf
  • Ministry of New and Renewable Energy, Government of India, Approved List of Models and Manufacturers (ALMM), Wind, as on 29 October 2026 · Suzlon S144: 3.0, 3.15 and 3.3 MW; rotor diameter 144 m; hub heights 105 to 160 m; https://mnre.gov.in/static/uploads/2026/10/c4d85161819b2e95f9779988953be330.pdf
  • The Wind Power (thewindpower.net), 'Suzlon S144/3000' turbine entry (read November 2026) · rated power 3 MW; rotor diameter 144 m; swept area 16,287 m2; https://www.thewindpower.net/turbine_en_1918_s144-3000.php
  • Energetica India, 'Suzlon announces its S144 - 3 MW series gets RLMM listing by MNRE' (16 November 2023) · listing of the S144 3 MW series; https://energetica-india.net/news/suzlon-announces-its-s144--3-mw-series-gets-rlmm-listing-by-mnre