Material Insights · Understanding the Material World

Heat and thermodynamics: engines, heat pumps and their limits

Every engine, refrigerator and power plant is a machine that moves heat, and two laws set what it can do. This module separates temperature, heat and stored energy, follows heat through walls, water and ice, audits a machine with the first law, derives the Carnot limit from the second, and works twelve estimates, from a pressure cooker and a thermal power plant's cooling water to an air conditioner, a heat pump and a cogeneration plant.

All courses / Understanding Engineering / Module 6

Heat and thermodynamics: engines, heat pumps and their limits

Every engine, refrigerator and power plant is a machine that moves heat, and two laws set what it can do. This module separates temperature, heat and stored energy, follows heat through walls, water and ice, audits a machine with the first law, derives the Carnot limit from the second, and works twelve estimates, from a pressure cooker and a thermal power plant's cooling water to an air conditioner, a heat pump and a cogeneration plant.

5 parts · 16 sections · about 50 minutes · 0 of 5 parts read

By the end you will be able to

  • Distinguish temperature, heat and internal energy, and estimate the heat needed to warm or change the phase of a mass of water
  • Estimate heat flow through a wall or roof by conduction and say how insulation reduces it
  • Use the first law to audit a machine and the second law to explain why no engine turns all its heat into work
  • Calculate the Carnot limit in kelvin and compare it with real steam, petrol, diesel and gas turbine plants
  • Explain why a refrigerator, air conditioner or heat pump can have a coefficient of performance above one
  • Judge a claim about waste heat recovery, cogeneration or a heat engine against the physical limits

Contents

  1. Part 1 Temperature, heat and the ways heat moves

    A cup of tea cools, a steel spoon in it grows warm, a terrace roof bakes in May and a cooker whistles on the stove. All four are heat on the move. This part separates temperature from heat and from internal energy, then follows heat through solids, fluids and empty space, and ends with the stores of heat that water and ice make possible.

    • Temperature says how hot a thing is, heat is energy on the move, and internal energy is what is stored
    • Heat moves by radiation, conduction and convection, and insulation works by choking all three
    • Specific heat and latent heat explain why a little water stores a lot of energy
  2. Part 2 The first and second laws: the audit and the limit

    Every heat machine is judged by two rules. The first law is a strict book-keeping rule: energy in must equal energy out plus change in store. The second law is a rule about quality, and it says that heat cannot be turned wholly into work. Together they let an engineer audit a machine on paper and know in advance the best it could ever do.

    • The first law is an energy audit: whatever goes in must come out or be stored
    • The second law says heat flows downhill, and entropy is the book-keeping that forbids a perfect engine
    • The Carnot limit: the best efficiency of any heat engine depends only on two temperatures
  3. Part 3 Real cycles: steam, petrol, diesel and gas turbine plants

    A cycle is the loop a working fluid follows so that a machine can run for ever: heat in, work out, heat rejected, back to the start. Almost every heat engine on the site is one of a few loops. This part takes each at the level of principle, estimates what it can reach, and shows how stacking two loops gives the best efficiencies ever achieved from fuel.

    • A steam power plant boils water, spins a turbine and sends nearly half of its fuel to the condenser
    • Condenser heat has to go somewhere, and for a plant that means a large flow of water
    • Petrol and diesel engines burn fuel inside the cylinder, and compression ratio sets their limit
    • A gas turbine burns fuel in a stream of air, and putting a steam plant on its exhaust gives the best efficiency yet
  4. Part 4 Refrigerators, air conditioners and heat pumps: moving heat uphill

    A heat engine lets heat fall from hot to cold and takes work from the fall. Run it backwards and you get a machine that spends work to lift heat from cold to hot: a refrigerator, an air conditioner or a heat pump. They are the same machine in three jobs. This part shows how the loop works, why it can deliver three or four units of heat for each unit of electricity, and what that means for a bedroom in May.

    • A refrigerator is a heat engine run backwards: a compressor lifts heat from a cold space to a warm one
    • The coefficient of performance can exceed one because the machine moves heat instead of making it
    • A heat pump is the same loop aimed at the room, and it warms water for a third of the electricity a geyser needs
  5. Part 5 Waste heat, cogeneration and judging a heat claim

    Most heat machines throw away more energy than they use, and that waste is a design problem, a cost and sometimes an opportunity. This part grades waste heat by temperature, works out what a simple recovery device saves, shows why generating power and heat together can use fuel far better than separate plants, and ends by giving the reader a short checklist for testing claims about heat engines and pumps.

    • Waste heat comes in grades, and its temperature decides what can be done with it
    • Cogeneration makes power and useful heat from one fuel supply, and saves about a fifth of the fuel
    • A short checklist lets you test any claim about a heat engine or heat pump
  6. Wrap-up Key terms, try it in the table, final quiz, sources
Start: Part 1, Temperature, heat and the ways heat moves →