Material Insights · Understanding the Material World

Heat and thermodynamics: engines, heat pumps and their limits: Temperature, heat and the ways heat moves

All courses / Understanding Engineering / Module 6: Heat and thermodynamics: engines, heat pumps and their limits Part 1 of 5

Temperature, heat and the ways heat moves

A cup of tea cools, a steel spoon in it grows warm, a terrace roof bakes in May and a cooker whistles on the stove. All four are heat on the move. This part separates temperature from heat and from internal energy, then follows heat through solids, fluids and empty space, and ends with the stores of heat that water and ice make possible.

1.1 Temperature says how hot a thing is, heat is energy on the move, and internal energy is what is stored

Three words are often used as if they meant one thing. Temperature measures the average energy of the jiggling of a body's molecules. Heat is energy that moves from one body to another because their temperatures differ. Internal energy is the whole store: the motion of all the molecules plus the energy held in their bonds. A bucket of tap water at 30 °C holds far more internal energy than a glowing matchhead at 600 °C, simply because the bucket has so many more molecules. Yet if the two touched, heat would flow from the matchhead to the water, because flow follows temperature, not the size of the store.

Heat is measured in joules, the same unit as the work of module 3 (Force, motion and energy). Heat and work are two ways of moving energy, and much of this module asks how much of one can become the other. Heat flow is a power, in watts. A 1 kW electric kettle element pushes 1,000 joules into the water every second.

Engineers use the kelvin scale whenever a ratio of temperatures matters, which is most of the time from here on. A kelvin step is the same size as a degree Celsius, but zero kelvin is the coldest possible state, about minus 273 °C. So kelvin = Celsius + 273. Room air at 27 °C is 300 K and a steam pipe at 540 °C is 813 K. In Celsius the pipe looks twenty times hotter than the room; in kelvin it is 2.7 times, and the kelvin ratio is the one the laws use. Two bodies in contact end up at one temperature, called thermal equilibrium, which is how a thermometer works: it settles to the temperature of what it touches.

The table lists temperatures that recur later.

Data Temperatures engineers meet, in Celsius and kelvin
CaseCelsiusKelvin
Cold-store freezer-20253
Comfortable room25298
Human body37310
Water boils at sea level100373
Water boils in a pressure cooker at about 2 bar absoluteabout 120about 393
Steam at the turbine of a coal plant540813
Peak gas temperature in a petrol engine cylinderabout 2,000about 2,300
Surface of the Sunabout 5,500about 5,800

Kelvin = Celsius + 273, rounded. Boiling point of water in the cooker from standard steam tables.

Source: Bloomfield, How Things Work (Wiley, 2015), ch. 7, 'Heat and Phase Transitions', section 7.1 (thermal energy, heat, temperature)
  • Bloomfield, How Things Work (Wiley, 2015) · ch. 7, 'Heat and Phase Transitions', section 7.1
  • Feynman, Leighton and Sands, The Feynman Lectures on Physics, vol. I (Caltech online edition) · further reading: ch. 39, 'The Kinetic Theory of Gases', https://www.feynmanlectures.caltech.edu/I_39.html

1.2 Heat moves by radiation, conduction and convection, and insulation works by choking all three

Stand on a flat concrete terrace in Nagpur on a May afternoon and all three ways heat travels are at work on one slab. Sunlight arrives as radiation, which needs no material to cross space, and a grey slab absorbs most of it, so its top climbs to 60 °C or more. Every surface also radiates, at a rate that rises with the fourth power of its absolute temperature.

The heat then works down through the concrete by conduction. Energy passes from molecule to neighbouring molecule while the material stays put. The rate follows one rule: heat flow = conductivity x area x temperature difference / thickness. Conductivity, in watts per metre per kelvin, spans a huge range: about 400 for copper, 200 for aluminium, 1.4 for dense concrete, 0.6 for water, 0.04 for mineral wool and 0.026 for still air.

Under the slab, the hot ceiling warms the air touching it, and convection, heat carried by a moving fluid, takes over. A ceiling fan forces it, spreading the warm layer through the room, while the ceiling also radiates onto anyone sleeping below. That is why a top-floor room stays hot long after sunset.

Insulation fights all three. Fibres and foams hold air nearly still, and a white or reflective coat on top sends sunlight back before it is absorbed. The trade-off is thickness, weight and money against heat kept out, with steeply falling returns: on this roof the first 50 mm of mineral wool removes about 92 per cent of the bare-slab flow and a second 50 mm only another 4 per cent (calculated). See the nodes Mineral wool insulation and Insulating glass unit, a window that uses a sealed gas gap to the same end.

The table works the numbers for a 30 m2 roof.

Data Worked estimate 1: heat through a 30 m2 terrace roof, bare and insulated
StepWorkingResult
Resistance of 150 mm concrete (k = 1.4 W/m K)0.15 m / 1.4 W/m K0.107 m2 K/W
Bare roof, top at 60 °C, ceiling at 26 °C (34 K)1 / 0.107 = 9.3 W/m2 K; 9.3 x 30 m2 x 34 Kabout 9,500 W
Add 50 mm mineral wool (k = 0.04 W/m K)0.05 / 0.04 = 1.25 m2 K/W; total 1.357 m2 K/WU = 0.74 W/m2 K
Insulated roof, same temperatures0.74 x 30 x 34about 750 W, nearly 13 times less
Both again, adding the still-air layer under the ceiling (about 0.17 m2 K/W)bare 1 / 0.277 = 3.6 W/m2 K; insulated 1 / 1.527 = 0.65 W/m2 Kabout 3,700 W against 670 W

All results calculated. The first four rows ignore the thin layer of still air under the ceiling; including it, at a standard design value of about 0.17 m2 K/W for heat flowing downwards, cuts the bare figure by more than half and the ratio to about five or six. The insulation still removes over four-fifths of the flow.

Source: Bloomfield, How Things Work (Wiley, 2015), ch. 7, 'Heat and Phase Transitions', sections 7.1 and 7.3 ('Woodstoves'; 'Clothing, Insulation, and Climate': conduction and thermal conductivity)
  • Bloomfield, How Things Work (Wiley, 2015) · ch. 7, 'Heat and Phase Transitions', sections 7.1 and 7.3 ('Woodstoves'; 'Clothing, Insulation, and Climate')
  • Feynman, Leighton and Sands, The Feynman Lectures on Physics, vol. I (Caltech online edition) · further reading: ch. 40, 'The Principles of Statistical Mechanics', https://www.feynmanlectures.caltech.edu/I_40.html

1.3 Specific heat and latent heat explain why a little water stores a lot of energy

Specific heat is the energy needed to warm one kilogram of a material by one kelvin. Water needs 4.19 kJ, which is unusually high; aluminium needs 0.9, dry soil about 0.8 and air about 1.0. Kilogram for kilogram, water holds four to five times as much heat per degree as rock or aluminium. The energy to warm any mass is mass x specific heat x temperature rise. The thermal mass of a thick wall and the milder climate of seaside Mumbai against inland Nagpur both follow from it.

Latent heat is energy taken in or given out while a material changes phase, with no change of temperature. Melting a kilogram of ice takes 334 kJ. Turning a kilogram of water into vapour takes about 2,260 kJ at 100 °C and about 2,430 kJ at 30 °C. The energy pulls molecules apart, and it all comes back on condensing or freezing.

Two Indian objects show how large these stores are. The ice-lined refrigerators that hold vaccines at health centres freeze a lining of water packs while the power is on; in a power cut, each kilogram of ice must absorb 334 kJ before it is gone, and the cabinet stays cold while it melts. An unglazed clay matka works the other way: water seeping through the wall evaporates, and 200 g a day leaving the pot carries away about 0.2 kg x 2,430 kJ/kg = 486 kJ, an average cooling of about 6 W (calculated), enough to keep the water several degrees below room air. Refrigerators and power plants use evaporating and condensing fluids for the same reason: a phase change moves a lot of heat per kilogram at a steady temperature.

Specific heat sets the size of everyday heat stores, and the rooftop solar water heater is the clearest case. The table works it for a 100 litre tank. The trade-off is that a bigger tank holds more heat but warms more slowly and loses more overnight, so tank and collector are sized together.

Data Worked estimate 2: a 100 litre solar water heater on a clear day
StepWorkingResult
Heat needed, 25 °C to 55 °C100 kg x 4.19 kJ/kg K x 30 K12,570 kJ = 3.5 kWh
Sun on a 2 m2 collector, clear day2 m2 x about 5.5 kWh/m2about 11 kWh
Collected, at about 45% system efficiency11 x 0.45about 5 kWh = 17.8 MJ
Possible temperature rise of 100 kg17,800 kJ / (100 x 4.19)about 42 K, so 25 °C to about 67 °C
Electric geyser to do the 3.5 kWh3.5 kWh / 2 kWabout 1.75 h of running

Results calculated. Check: sold systems of this size are rated at 100 litres a day at 50 to 60 °C, and the estimate lands in the same range. Insolation of 5 to 6 kWh/m2 a day is typical for much of India on clear days; the 45 per cent collection efficiency is an assumed round value.

Source: Bloomfield, How Things Work (Wiley, 2015), ch. 7, 'Heat and Phase Transitions', sections 7.1 and 7.2 ('Woodstoves'; 'Water, Steam, and Ice': specific heat, latent heat)
  • Bloomfield, How Things Work (Wiley, 2015) · ch. 7, 'Heat and Phase Transitions', sections 7.1 and 7.2 ('Woodstoves'; 'Water, Steam, and Ice')
  • Kosky et al., Exploring Engineering (Academic Press, 2013) · ch. 4, 'Energy Conversion', section 4.3 (kinds of energy)

See it in the table

H₂O WaterCu CopperAl AluminiumWl Wool

Check your understanding

A small matchhead at 600 °C touches a large bucket of water at 30 °C. Which statement is right?

Heat flows from higher temperature to lower temperature regardless of how large each store is. The bucket has more internal energy because it has far more molecules, but the match is hotter, so the flow is from match to water.

Why does 50 mm of mineral wool change the roof estimate so strongly?

Resistance is thickness divided by conductivity: 1.25 for the wool against 0.107 for the slab. Resistances in series add, so the layer of air-filled fibre dominates the total.

In a power cut, why does a vaccine refrigerator with an ice lining stay cold for hours?

While ice and water are both present, heat that leaks in is spent loosening bonds as the ice melts, not raising the temperature. Each kilogram soaks up 334 kJ, so a few tens of kilograms of ice give a large buffer.
← Module contentsMark read · Part 2: The first and second laws: the audit and the limit →