Material Insights · Understanding the Material World

Aluminium can: Bill of materials

About these figures

Which unit, study and year the composition figures describe, and how they vary

The composition is for a 330 ml can of 12 g, the European average in 2018 data [12], with the make-up of the average North American can in the 2021 Aluminum Association study: 12.99 g of metal, 0.457 g of coatings and 0.0144 g of ink, 13.46 g in all [6], scaled by mass (calculated). Manganese and magnesium are worked out from typical alloy contents [22] and Ball's body and end weights [1] (calculated). Variants differ only in recycled share. Can sheet is a component not yet a node and is listed as a new product.

as of 2026-11-16

Direct materials

The commodities and chemicals in one unit as bought, with amount, mass share, cost share and recycled content

Variant 1 Primary can
MaterialRoleAmount in one unitShare of the unit's massRecycled content
Al AluminiumStructural0.011 kgrange 0.011 to 0.012 kg 94.01%0%
Calculated: a 12 g, 330 ml can [12] holds 11.58 g of metal at the North American study's 12.99 of 13.46 g [6], less the manganese and magnesium below; here made wholly from new aluminium. Bauxite and alumina behind it are not nodes in the catalogue: 4 t of dried bauxite give 2 t of alumina and 1 t of aluminium [21]. Low and high are the same shares of an 11.9 g can (Ball, calculated) [1] and a 13 g can [24].
Variant 2 Average can
MaterialRoleAmount in one unitShare of the unit's massRecycled content
Al AluminiumStructural0.011 kgrange 0.011 to 0.012 kg 94.01%73%
Calculated: a 12 g, 330 ml can [12] holds 11.58 g of metal at the North American study's 12.99 of 13.46 g [6], less the manganese and magnesium below; 73% recycled metal, with primary aluminium 26.6% of raw metal input [6]. Bauxite and alumina behind it are not nodes in the catalogue: 4 t of dried bauxite give 2 t of alumina and 1 t of aluminium [21]. Low and high are the same shares of an 11.9 g can (Ball, calculated) [1] and a 13 g can [24].
Variant 3 Recycled can
MaterialRoleAmount in one unitShare of the unit's massRecycled content
Al AluminiumStructural0.011 kgrange 0.011 to 0.012 kg 94.01%100%
Calculated: the same mass made wholly from recycled metal, a limiting case. Bauxite and alumina behind it are not nodes in the catalogue: 4 t of dried bauxite give 2 t of alumina and 1 t of aluminium [21]. Low and high are the same shares of an 11.9 g can (Ball, calculated) [1] and a 13 g can [24].
Variant 4 Not stated
MaterialRoleAmount in one unitShare of the unit's mass
Pnt Paints and coatingsFunctional0 kg3.39%
Calculated: coatings of 0.457 kg per 1,000 North American cans of 13.46 kg [6], scaled to a 12 g can; inks add about 0.013 g (0.0144 kg per 1,000 cans [6], 0.11% of mass). The inside lacquer is now often BPA-NI, based on acrylic emulsion and polyester resins; epoxy resins were the traditional lining [39].
Mg MagnesiumFunctional0 kg1.66%
Calculated: about 1% in the 3004 body and 4.5% in the 5182 end [22], same split. It is the main strengthening element of the lid.
Mn ManganeseFunctional0 kg0.83%
Calculated: about 1% in the 3004 body and 0.3% in the 5182 end [22], with the body 79.4% and the end 20.6% of the metal, from Ball's 9.43 g body and 2.44 g end [1], applied to 11.58 g of metal. Sits inside the alloy, so it is not added to the aluminium row.

as of 2026-11-16

How it is put together

The main steps from parts and materials to the finished unit

StepWhat happensTechnologySource
Mine and refineBauxite is refined to alumina by the Bayer process; about 4 t of dried bauxite give 2 t of alumina, which gives 1 t of aluminium [21]Bayer alumina process[21]
Smelt new aluminiumElectrolysis of alumina uses about 14.1 MWh of electricity per tonne of aluminium on the global average [28]Hall-Heroult aluminium smelting[28]
Melt and castScrap and ingot are melted together and cast; the can body and the lid use different alloys [6]– [6]
Roll the sheetIngots are preheated to about 1,000 degrees Fahrenheit (about 540 degrees Celsius) and hot rolled; coils may be annealed, then cold rolled to about 0.3 mm; lid stock is cleaned and coated [6]– [6]
Cup, draw and ironDiscs are stamped into cups about 88 mm across, redrawn, then ironed past rings that thin the wall; the base is domed [33][23]– [33][23]
Wash, coat and decorateTrimmed cans are washed and dried, painted outside and coated inside as a barrier between metal and drink [6]– [6]
Neck and flangeThe open end is narrowed to match the lid diameter [6]– [6]
Fill and seam the lidThe bottler fills the can and seams on the end, which is made in a separate line from lacquered coil [23]– [23]

as of 2026-11-16

Technologies used to make it

The technologies used to make it, at which step

Made with

as of 2026-11-16

Sources

  1. Beverage packaging – A Comparative Life Cycle Assessment Sphera for Ball Corporation, 2020
  2. Life Cycle Assessment of North American Aluminum Cans Sphera for The Aluminum Association, 2021
  3. Life Cycle Assessment of Metal Packaging in Europe: executive summary Metal Packaging Europe, 2022
  4. Mineral Commodity Summaries 2026: Bauxite and Alumina USGS, 2026
  5. Sheet aluminum alloys for cans and cars The Fabricator
  6. An aluminium beverage can Aluminium Guide, 2020
  7. Lightweight (Alustory: packaging) International Aluminium Institute (Alustory)
  8. Factsheet: Aluminium smelting with use of low-carbon electricity GIZ, 2025
  9. The Comeback of the Aluminum Can, Part 2 ASME, 2018
  10. Toyochem launches new BPA-NI internal coatings for metal cans Coatings World