Flexible plastic packaging film: Bill of materials
About these figures
Which unit, study and year the composition figures describe, and how they vary
The amounts are a mass balance, one tonne of polymer for one tonne of film, from the sizing of a US blown-film model [2]. Real films also carry additives and, in laminates, adhesives, inks and barrier layers such as EVOH or nylon [7]. No source gives their amounts per tonne. EVOH film, carrier bags and pouches are not yet nodes.
as of 2026-11-17
Direct materials
The commodities and chemicals in one unit as bought, with amount, mass share, cost share and recycled content
Variant 1 Polyethylene film| Material | Role | Amount in one unit | Share of the unit's mass |
|---|---|---|---|
| LLDPE Polyethylene (LDPE, LLDPE) | Structural | 1000 kg | – |
| Calculated: a US blown-film model is sized for 1 tonne of film from 30% recycled flexible plastic and 70% LDPE, so about one tonne of polymer goes in per tonne of film [2]. Additive content not found. | |||
| HDPE High-density polyethylene | Structural | Not given | – |
| HDPE is also blown into film; no amount per tonne was found. | |||
| Add Polymer additives | Functional | Not given | – |
| Added to the pellets before extrusion; no amount per tonne found. | |||
| PA Nylon (PA6, PA66) | Functional | Not given | – |
| Polyamide 6 is one of the layer polymers compared in an LCA of 14 multilayer films [7]; amount per tonne not found. | |||
| Adh Adhesives and sealants | Consumable | Not given | – |
| Laminating adhesive joins layers in multilayer films; amount per tonne not found. | |||
| Material | Role | Amount in one unit | Share of the unit's mass |
|---|---|---|---|
| PP Polypropylene | Structural | 1000 kg | – |
| Calculated on the same one-tonne-in, one-tonne-out basis as the polyethylene film [2]; additive content not found. | |||
as of 2026-11-17
How it is put together
The main steps from parts and materials to the finished unit
| Step | What happens | Technology | Source |
|---|---|---|---|
| Make the polymer | Ethylene is polymerised at very high pressure to make low-density polyethylene [9]. | High-pressure polyethylene process | [9] |
| Make the other resins | Polypropylene and linear polyethylene are made with catalysts at lower pressure. | Ziegler-Natta polymerisation | – |
| Compound | Pellets are mixed with additives and any recycled polymer before extrusion. | – | – |
| Extrude the film | An extruder melts the pellets and forces the melt through an annular die; air inflates the tube [8]. | – | [8] |
| Cool and wind | Chilled air cools the bubble, which is flattened, pulled up by nip rollers and wound [8]. | – | [8] |
| Stretch (polypropylene) | BOPP film is stretched in both directions to orient the chains. | – | – |
| Convert | Rolls are printed, laminated, slit and sealed into bags and pouches. | – | – |
as of 2026-11-17
Technologies used to make it
The technologies used to make it, at which step
Made with- LDPE High-pressure polyethylene process Making low-density polyethylene resin The resin for much blown polyethylene film comes from this process; no share found.
- ZN Ziegler-Natta polymerisation Making polypropylene and linear polyethylene resin No share of film made from catalyst-made resin found.
as of 2026-11-17
Sources
- Economic and environmental feasibility of recycling flexible plastic packaging from single stream collection (INL/JOU-21-64510) Idaho National Laboratory for the US Department of Energy, 2023
- A cradle-to-grave life cycle assessment of multilayer plastic film food packaging materials, comparing to a paper-based alternative Waste Management 200, 114747 (Mousania and Atkinson), 2025
- What is blown film extrusion? FKuR
- Polyethylene: discovered by accident 75 years ago ICIS (Anna Jagger), 2008