Material Insights · Understanding the Material World

Grain-oriented electrical steel: Working

What it is

The product and the job it does, in a short paragraph

Grain-oriented electrical steel is a thin silicon steel sheet, with silicon above 3%, in which most crystals point the same way along the rolling direction [1]. That alignment makes it easy to magnetise, so transformer cores built from it waste little energy as heat. This node covers cold-rolled grain-oriented sheet and strip (CRGO, HS 7225.11 and 7226.11), in conventional and high-permeability grades. The functional unit is one tonne. Non-oriented steel for motors is left out.

as of 2026-11-15

How it works

How it does its job, step by step in plain words

Iron is magnetic because of small regions called domains. In a transformer core the alternating field makes these domains flip many times a second, and each flip wastes some energy. When the crystals are lined up along the sheet, the domains flip easily and the loss is low [7]. Silicon raises the sheet's electrical resistance, which limits the currents that swirl inside it [7], and rolling it to 0.2 to 0.35 mm thick limits them further [7][8]. A final anneal above 1,100 C for more than 10 hours grows the aligned crystals [17]. An insulating coating separates the stacked sheets, and a laser can refine the domains further [8].

as of 2026-11-15

Key specifications

The numbers that describe it, each with unit, variant, year and source

SpecValueUnitVariantYearSource
Silicon content of the hot-rolled base strip3.2% of mass– 2021[4]; normally below 3.30% [7]
Sheet thickness range of one maker's grain-oriented range0.20 to 0.35mm– 2026[8]
Maximum core loss at 1.7 T and 50 Hz, grade 23Z110 (0.23 mm)1.1W per kgConventional2026[8]
Maximum core loss at 1.7 T and 50 Hz, grade 35Z155 (0.35 mm)1.55W per kgConventional2026[8]
Maximum core loss at 1.7 T and 50 Hz, grade 23ZH85 (0.23 mm)0.85W per kgHigh-permeability2026[8]
Maximum core loss at 1.7 T and 50 Hz, laser domain-refined grade 20ZDKH65 (0.20 mm)0.65W per kgHigh-permeability (laser domain-refined)2026[8]
Flux density at B10 compared with conventional grades0.1T higherHigh-permeability2026[8]
Typical grain size (the review gives the rise from about 0.3 mm to 10 mm with high permeability)0.3mmConventional2025[7]
Typical grain size10mmHigh-permeability2025[7]

as of 2026-11-15. Core loss is a grade's guaranteed maximum W17/50 (1.7 T, 50 Hz) from one maker's catalogue [8]: conventional and high-permeability grades are tested after stress-relief annealing, the laser grade as sheared. Other makers' grades differ.

Variants

The variants whose make-up or footprint differs a lot, what defines each and its share of units

VariantDefining specYearSource
ConventionalCrystals about 7 degrees off the ideal Goss direction, grains about 0.3 mm; one maker's range runs 0.23 to 0.35 mm at up to 1.55 W per kg2025[7][8]; no share of sales found
High-permeabilityCrystals within about 3 degrees of the ideal direction, grains about 10 mm, made with an aluminium nitride inhibitor and one-stage cold rolling; laser domain-refined grades go down to 0.65 W per kg; the top permanently refined grade comes only from Nippon Steel2025[7][8][2]; no share of sales found

as of 2026-11-15. The DOE names grades CGO, HI-B, PDR and MOH [2]; domain-refined grades are counted here with high-permeability because they start from it [8].

Limits

The physical limits set by science and the engineering limits of today's design, with today's value

LimitKindLimitTodayUnitSource
Saturation flux density of silicon iron (best texture reaches B8 of 2.0 T)Physical2.032T[7]
Silicon content above which the steel loses ductility and is hard to cold roll thinEngineering3.33.2% of mass[7][4]
Thinnest sheet in one maker's standard grain-oriented rangeEngineering– 0.2mm[8]

as of 2026-11-15

Science it relies on

The science principles it works by or is limited by

Relies on

as of 2026-11-15

Sources

  1. Electric Grid Supply Chain Review: Large Power Transformers and High Voltage Direct Current Systems US Department of Energy, 2022
  2. Large Power Transformer Resilience: Report to Congress US Department of Energy, 2024
  3. Environmental Product Declaration EPD-TKE-20240546-CBC1-EN: powercore grain oriented electrical steel thyssenkrupp Electrical Steel, programme holder Institut Bauen und Umwelt e.V. (IBU), 2025
  4. The processing, microstructure, texture, and magnetic properties of electrical steels: A review (He and Kestens, International Materials Reviews 70(5), 353-393) TU Delft repository copy, 2025
  5. Grain-Oriented Electrical Steel Sheets (ORIENTCORE product page) Nippon Steel Corporation, 2026
  6. Technologies for high-temperature batch annealing of grain-oriented electrical steel: An overview (Open Engineering 14) De Gruyter, Cardiff University repository copy, 2024