PET bottle: Bill of materials
About these figures
Which unit, study and year the composition figures describe, and how they vary
Composition is for a 500 ml still-water bottle: a 12.9 g body measured on one UK bottle and a 1.6 g HDPE cap estimated in a 2020 European study [35]. Carbonated-drink bottles are heavier (20 to 28 g in 2009 [8]). The recycled variant swaps virgin resin for recycled PET. Labels, barrier layers and colourants are not covered. Components not yet nodes: the preform and the closure; both are listed as new products.
as of 2026-11-16
Direct materials
The commodities and chemicals in one unit as bought, with amount, mass share, cost share and recycled content
Variant 1 Virgin PET bottle| Material | Role | Amount in one unit | Share of the unit's mass | Recycled content |
|---|---|---|---|---|
| PET PET resin | Structural | 0.013 kg | 89% | 0% |
| Body resin of a 500 ml water bottle, 12.9 g as measured on one UK bottle in a 2020 European study [35]; mass share 12.9 of 14.5 g with the cap (calculated). The PTA, MEG and paraxylene behind it are counted in the PET resin node. | ||||
| HDPE High-density polyethylene | Structural | 0.002 kg | 11% | – |
| HDPE screw cap of that bottle, 1.6 g as estimated by the study [35]; caps for carbonated drinks weigh about 2.4 g [11]. Some caps use polypropylene [37]. | ||||
| Sb Antimony | Functional | 0 kgrange up to 0 kg | – | – |
| Polycondensation catalyst; typically below 300 mg per kg PET [9], so at most about 3.9 mg in a 12.9 g body (calculated). It sits inside the resin mass, so it has no mass share of its own. | ||||
| Material | Role | Amount in one unit | Share of the unit's mass | Recycled content |
|---|---|---|---|---|
| PET PET resin | Structural | 0.013 kg | 89% | 100% |
| Same 12.9 g body [35] from recycled PET flake or pellets; 100% recycled content is possible [2]. Food-grade rPET is needed for drinks. | ||||
| HDPE High-density polyethylene | Structural | 0.002 kg | 11% | – |
| Same 1.6 g cap as the virgin bottle [35]. | ||||
Indicative · as of 2026-11-16
How it is put together
The main steps from parts and materials to the finished unit
| Step | What happens | Technology | Source |
|---|---|---|---|
| Make the monomers | Paraxylene is oxidised to purified terephthalic acid (PTA) [5]; monoethylene glycol (MEG) comes from ethylene. PET is made from terephthalic acid and ethylene glycol [9]. | – | [5][9] |
| Polymerise to resin | PTA and MEG (molar ratio 1:1.15, with about 2% isophthalic acid) react at about 280 degrees Celsius with an antimony catalyst, then in melt polymerisation at about 300 degrees Celsius [5] | – | [5] |
| Raise the chain length | Solid-state polymerisation in hot nitrogen takes about 15 hours and gives bottle-grade resin [5] | – | [5] |
| Mould the preform | Dry resin is injection moulded into a thick-walled preform with the cap thread already formed [12][9] | Injection moulding | [12][9] |
| Reheat and stretch blow | The preform is reheated, placed in a bottle mould and blown with air that stretches it outwards and downwards [13]. Preheating takes about 0.15 kWh per kg of preforms [10]. | – | [13][10] |
| Mould the cap | The cap is injection moulded from HDPE: about 1.6 g for a water bottle [35] and 2.4 g for a carbonated-drink cap [11] | Injection moulding | [35][11] |
| Fill and cap | The bottler fills the bottle and screws the cap on. Making preforms and blowing can be done in two separate stages or in one machine [12]. | – | [12] |
as of 2026-11-16
Technologies used to make it
The technologies used to make it, at which step
Made with- IM Injection moulding Moulding the preform and the cap Preforms are injection moulded in one-stage and two-stage machine systems [12]. Stretch blow moulding has no technology node yet.
as of 2026-11-16
Sources
- PET Plastic Bottles Have A Significantly Lower Environmental Impact Compared to Glass Bottles and Aluminum Cans NAPCOR, 2023
- Decarbonisation options for the Dutch bottle-grade PET industry PBL Netherlands Environmental Assessment Agency and TNO (Tran and West), 2021
- Optimising the weight of PET packaging Plastech.pl, 2009
- The Facts about PET Dr Frank Welle, Fraunhofer IVV (hosted by Petcore Europe)
- Boosting Energy and Resource Efficiency in the Manufacture of PET Bottles KHS Corpoplast, on PETnology online, 2010
- New BERICAP Neck Finish According to New ISBT's PCO 1881 Packaging Insights (CNS Media), 2006
- No. 9 - Stretch-Blow Molding Plastics Technology (ptonline.com), sponsored by WSB Gravimetric Blenders
- Soda Bottle How Products Are Made (Gale), on Encyclopedia.com
- Beverage packaging – A Comparative Life Cycle Assessment Sphera for Ball Corporation, 2020
- Short, Shorter, the Shortest Packaging Digest (Anton Steeman), 2014