Printed circuit board: Bill of materials
About these figures
Which unit, study and year the composition figures describe, and how they vary
Per square metre of a four-layer FR-4 board, a 2021 life cycle inventory lists 2.87 kg of copper, 1.21 kg of copper foil, 1.89 kg of glass fibre and 0.14 kg of phenolic resin as inputs [6]; much of the copper is etched away. Scrap boards in recycling studies are typically 40% metals, 30% organics and 30% ceramics [7]. Glass fibre fabric, copper foil and copper clad laminate are not yet nodes.
as of 2026-11-15
Direct materials
The commodities and chemicals in one unit as bought, with amount, mass share, cost share and recycled content
Variant Rigid| Material | Role | Amount in one unit | Share of the unit's mass |
|---|---|---|---|
| Cu Copper | Functional | 2.87 kgrange 2.87 to 4.08 kg | – |
| Copper used to make one m2 of four-layer FR-4 board in the 2021 inventory; the same table lists 1.21 kg of copper foil separately, so the upper figure (calculated) adds it. Much of this copper is etched away, so the finished board holds less [6]. | |||
| HCl Hydrochloric acid | Consumable | 2.49 kg | – |
| Etching chemical per m2 in the 2021 inventory [6]. | |||
| H2O2 Hydrogen peroxide | Consumable | 1.46 kg | – |
| Etching chemical per m2 in the 2021 inventory [6]. | |||
| H2SO4 Sulphuric acid | Consumable | 0.99 kg | – |
| Process chemical per m2 [6]; 0.86 kg of iron(III) chloride is also used [6]. | |||
| EPX Epoxy resins | Structural | Not given | – |
| FR-4 is epoxy resin, woven glass fibre and copper foil [6], and the resin is typically bromine-filled [18]; the 2021 inventory lists only 0.14 kg of phenolic resin and gives no epoxy mass [6]. | |||
| Sn Tin | Functional | Not given | – |
| Surface finish and solder: traditionally tin-lead [19]; no bare-board mass found. | |||
| Ni Nickel | Functional | Not given | – |
| Layer under gold in the electroless nickel immersion gold (ENIG) finish [19]; no mass found. | |||
| Au Gold | Functional | Not given | – |
| Thin gold coating in ENIG and direct gold finishes [19]; no mass found. | |||
as of 2026-11-15
How it is put together
The main steps from parts and materials to the finished unit
| Step | What happens | Technology | Source |
|---|---|---|---|
| Make the laminate | Woven glass cloth is bonded with flame-retardant epoxy and copper foil into a copper clad sheet. | – | [18][6] |
| Etch the circuit | Copper is etched away with acids, hydrogen peroxide and iron(III) chloride, leaving the tracks. | – | [6] |
| Stack the layers | Etched layers are separated by insulating substrate to build a multilayer board. | – | [19] |
| Drill and plate holes | Holes are drilled through the stack and their walls are plated with copper to join layers. | Electroplating | [19] |
| Apply solder mask | A polymer solder resist covers areas that must not be soldered. | – | [19] |
| Apply surface finish | Exposed pads get a finish such as organic coating, immersion silver, ENIG or gold, since bare copper oxidises quickly. | – | [19] |
as of 2026-11-15
Technologies used to make it
The technologies used to make it, at which step
Made with- Ep Electroplating Plating the walls of drilled holes with copper Hole walls are plated with copper to form plated-through holes that join the layers [19].
as of 2026-11-15
Sources
- Alternative Materials for Printed Circuit Board Production: An Environmental Perspective Sustainability (MDPI), Nassajfar, Deviatkin, Leminen and Horttanainen, 2021
- Recycling of Printed Circuit Boards (Integrated Waste Management, Volume II) InTech, Maria Paola Luda (in Integrated Waste Management, Volume II), 2011
- FR4 PCB Deep Guide: Material Truth, Real Specs and When to Use (or Avoid) It JLCPCB, 2025
- Printed circuit board New World Encyclopedia