Material Insights · Understanding the Material World

Printed circuit board: Footprint

Raw materials in one unit

Every commodity and chemical inside one unit, traced through its components by the site, with its emission factor and emissions

VariantMaterialAmount (kg)Emission factor (kg CO2e per kg)Emissions (kg CO2e)
RigidCopper2.873.96511.4
RigidHydrochloric acid2.49– –
RigidHydrogen peroxide1.46– –
RigidSulphuric acid0.99– –

Worked out from data

The site's estimate

Emissions of one unit worked out by the site from its materials and energy, for the world and India, with the share of mass covered by emission factors

VariantStagePlaceEmissions (kg CO2e)Mass covered by factors
RigidMakingWorld19637%
RigidUseWorld– –
RigidMakingIndia27037%
RigidUseIndia– –

Worked out from data

Energy to make it

Energy used to make one unit, by carrier and stage

Energy to make
  • El Electricity 20 kWh · Manufacturing Rigid Assumed in a 2021 study for one m2 of four-layer FR-4 board, which estimates 18 to 25 kWh; studies it cites give from about 6 kWh (a panel of four-layer board) to 20 kWh [6].
  • El Electricity 326 kWh · Manufacturing Rigid six-layer The ecoinvent dataset for manufacturing one m2 of six-layer FR-4 board, as quoted in the 2021 paper; the paper gives no reason for the gap to its own 20 kWh for four layers [6].
  • Ht Heat 105 kWh · Manufacturing Rigid six-layer Heat in the same ecoinvent six-layer entry [6].

as of 2026-11-15

Emissions by stage

Published life-cycle emissions of one unit in four stages (making, logistics, use, end of life), with their split, place and variant

StageValueUnitVariantPlaceYearSource
Making17.7kg CO2e per m2Rigid FR-4 (standard board)Not stated2020Environmental Resources Management (2020) figure for one square metre of standard FR-4 PCB, quoted by the laminate maker Jiva Materials; layer count and system boundary not given [9]

as of 2026-11-15. Only the making stage is published per square metre, so stage shares cannot be given. A bare board uses no energy itself; its use and end of life are counted with the device. The figure comes from a maker of a competing laminate, so treat it as indicative. Electricity generation is 41% of a four-layer board's climate impact in one study [6]. Substrate material alone is about 20 kg CO2e per kg for FR-4 and polyimide [8].

End of life

What happens to a unit when it is thrown away: collection, reuse, recycling and disposal shares, by place

RouteSharePlaceYearSource
All e-waste: documented as properly collected and recycled (no PCB-specific split found)22.3World2022[15]

as of 2026-11-15

Recovered as

The commodities and chemicals recovered at end of life, with recovery rates

Recovered as 4
  • Cu Copper 68.4% recovered · Recycling A pyrometallurgical process in a study quoted by the review recovered 68.4% of copper from scrap boards [7].
  • Ag Silver 92.6% recovered · Recycling 92.6% in the same pyrometallurgical process; a hydrometallurgical flowsheet recovered 93% [7].
  • Au Gold 85.5% recovered · Recycling 85.5% by pyrometallurgy; 95% in a hydrometallurgical flowsheet. About 90% of the intrinsic value of most scrap boards is in gold and palladium [7].
  • Pd Palladium 99% recovered · Recycling 99% in a hydrometallurgical flowsheet quoted by the review [7].

as of 2026-11-15

End of life in India

Collection and recycling in India, including the informal sector

A bare board has no sourced collection rate of its own; it is recycled with the device it sits in. Only 22.3% of the world's 62 million tonnes of e-waste was documented as properly collected and recycled in 2022 [15]. India's E-Waste Rules 2022 apply extended producer responsibility from 1 April 2023, and 72 registered refurbishers added about 92,042 tonnes a year of capacity [16]. The government says no authentic estimate exists of the share handled by the informal sector [16].

as of 2026-11-15

Water and waste

Water use and waste per unit where a source gives them

MeasureValueUnitStageYearSource
Water used per m2 of four-layer FR-4 board (inventory input)23.97kgManufacturing2021[6]
Etching and process chemicals (hydrochloric acid, hydrogen peroxide, iron(III) chloride, sulphuric acid and others) per m2, excluding water (about 33 kg with water)9kgManufacturing2021Calculated from [6]: 2.49 + 1.46 + 0.86 + 0.99 kg listed; others not itemised

as of 2026-11-15

Sources

  1. Alternative Materials for Printed Circuit Board Production: An Environmental Perspective Sustainability (MDPI), Nassajfar, Deviatkin, Leminen and Horttanainen, 2021
  2. Recycling of Printed Circuit Boards (Integrated Waste Management, Volume II) InTech, Maria Paola Luda (in Integrated Waste Management, Volume II), 2011
  3. ReCollect: Efficient Manufacturing of Recyclable Composite Laminates for Electrical Goods (webinar slides) Jiva Materials Ltd, hosted by the Institute of Circuit Technology (carbon figures from Environmental Resources Management, 2020), 2020
  4. Global e-Waste Monitor 2024: Electronic Waste Rising Five Times Faster than Documented E-waste Recycling UNITAR, 2024
  5. E-Waste (Management) Rules (2022): Assessing India's Extended Producer Responsibility Framework IMPRI India (Sudeepti Joshi), 2026