Gas turbines and combined cycle: Engineering methods
Combined cycle, fast peakers and jet engines from one core
The same gas turbine core is used three ways: with a steam bottoming cycle, alone for fast peaking, or with a fan for flight.
Comparison
| Method | Efficiency | Scale | Economics | Limitations | Reliability |
|---|---|---|---|---|---|
| Combined-cycle gas plant (CCGT)123456121428 | about 64% rated, 57% best field; US units built 2010-2022 about 49% and all US gas plants about 44% (both calculated from heat rates, HHV) | about 630-1,230 MW per block in EIA reference plants; Egypt's Beni Suef, New Capital and Burullus plants total 14.4 GW (3 x 4.8 GW) | USD 48-109/MWh | Exposed to gas prices; turbine order queues of four to five years. | Weighted forced outage rate of North American combined-cycle units was 5.7% in 2025 (4.2% in 2024); hot-section parts need scheduled replacement; fleets run 30 years or more. |
| Open-cycle / peaker plant1514 | about 31-33% (calculated from Lazard's 10,275-11,175 Btu/kWh, HHV); EIA reference units about 36-37% (calculated from 9,142-9,447 Btu/kWh); best simple-cycle ratings 42-44% (LHV) | about 210-420 MW per unit in EIA reference plants; aeroderivatives are much smaller | USD 149-251/MWh at 10-15% utilisation | Low efficiency; costly per MWh. | Aeroderivatives reach full power in minutes and tolerate frequent starts. |
| Jet engines (turbofans)8 | about 40% overall | one engine per wing on most airliners | A narrowbody fleet needs thousands of new engines a year. | Weight and safety limit cycle choices; 20-30% of core air is spent cooling the hot section. | Hot sections must survive long lives at material temperatures of about 1,200-1,650 C (2,200-3,000 F); efficiency falls several percent between overhauls. |
Combined cycle is the efficiency leader at about 64% and the lowest-cost firm power where gas is cheap, but it is capital-intensive and now faces multi-year turbine queues. Peakers trade efficiency (31-44%) for low capital cost and fast starts, so they suit few hours a year. Jet engines optimise thrust per kilogram rather than efficiency alone and reach about 40% overall. All three share the same superalloy hot section, the same makers' supply bottlenecks and the same wear-driven maintenance cycles.
How each method works
Combined-cycle gas plant (CCGT)One or more gas turbines exhaust into heat recovery steam generators that feed a steam turbine. Arrangements range from single-shaft 1x1 units to multi-shaft 3-on-1 blocks.
Open-cycle / peaker plantA gas turbine alone, either a heavy industrial frame or a lighter aeroderivative adapted from a jet engine, started when demand peaks.
Jet engines (turbofans)The core drives a large fan; most thrust comes from air bypassing the core. Higher pressure ratios, hotter turbines and bigger, slower fans raise efficiency.
Sources
- Gas Turbines: Past, Present and Future (Efficiency Focus), S.C. Gulen, UTSR Project Review Meeting US DOE National Energy Technology Laboratory, 2021
- GE HA Turbine Snags Another World Record for CCGT Efficiency POWER Magazine, 2018
- Electric Power Annual, Table 8.1: Average Operating Heat Rate for Selected Energy Sources, 2015 through 2025 US Energy Information Administration, 2026
- Natural gas combined-cycle power plants increased utilization with improved technology US Energy Information Administration, Today in Energy, 2023
- Lazard's Levelized Cost of Energy+ (LCOE+), June 2025 Lazard, 2025
- GE Vernova gas turbine backlog climbs to 116 GW Utility Dive, 2026
- Commercial Aircraft Propulsion and Energy Systems Research, Chapter 3: Aircraft Gas Turbine Engines National Academies of Sciences, Engineering, and Medicine, 2016
- Generators for power generation (product overview and references) Siemens Energy, 2025
- Assumptions to the Annual Energy Outlook 2026: Electricity Market Module (Table 3, cost and performance of new generating technologies) US Energy Information Administration, 2026
- NERC: Conventional generation outages rose as reliability risks become more systemwide (2026 State of Reliability) Power Engineering, 2026