Gas turbines and combined cycle: Science and limits
How hotter blades and recycled exhaust push efficiency to 64%
A gas turbine sucks in air, squeezes it, burns fuel in it and lets the hot gas expand through a turbine that drives both the compressor and a generator (or, in a jet engine, pushes the aircraft). A combined-cycle plant catches the still-hot exhaust to raise steam for a second turbine, reaching about 64% efficiency, the best of any heat engine in service.
The conversion, step by step
CombustionChemical (natural gas or jet fuel) → Heat in compressed air · better than 99% of the fuel burns8Gas turbine (Brayton cycle)
Heat → Mechanical (shaft) · about 42-44% of fuel energy in the best simple-cycle units; the exhaust leaves at about 650 C127Heat recovery steam generator and steam turbine
Exhaust heat → Mechanical · adds about one third of the combined plant's output1Generator
Mechanical → Electrical · up to 98.9% (air-cooled)15Whole combined-cycle plant
Chemical (gas) → Electrical · about 64% rated (net, LHV); about 57% best field performance; about 44% for all US gas-fired plants in 2025 (calculated from EIA's 7,781 Btu/kWh, HHV)13Jet engine (turbofan)
Chemical (jet fuel) → Kinetic energy of the aircraft · about 40% overall: up to 55% thermal times 70-80% propulsive8
The science
The gas turbine runs the Brayton cycle: compress, heat at roughly constant pressure, expand. Because the compressor absorbs a large share of the turbine's work, efficiency depends on the pressure ratio and above all on how hot the gas entering the turbine is. Modern H- and J-class machines run turbine inlet gas at about 1,600-1,650 C, hotter than the melting point of the nickel superalloy blades, which survive only because cooling air flows through internal passages and out through tiny holes, and a ceramic thermal barrier coating shields the metal. A simple-cycle machine throws away exhaust at about 650 C. Combined cycle uses this as the heat source for a Rankine steam cycle, so the plant uses heat across a far wider temperature span. A jet engine is the same core with the turbine power used to drive a large fan; propulsive efficiency rises when a big fan moves a lot of air slowly rather than a little air fast.
Limits set by science
| Limit | Value | Why it exists | Best today |
|---|---|---|---|
| Carnot limit for combined cycle | about 85% (calculated: 1 - 288 K / 1,923 K, for 1,650 C turbine inlet and 15 C ambient air)1216 | Heat is not all added at the peak temperature, so the practical ceiling is lower than this. | About 64% rated net efficiency (LHV), roughly three quarters of the Carnot figure (calculated). Measured records: 62.22% at Bouchain, France (2016) and 63.08% gross at Nishi-Nagoya, Japan (2018, Guinness-recognised). Mitsubishi reports more than 64% (LHV) at its T-Point 2 validation plant (company claim). |
| Ideal Brayton cycle | about 59% at a pressure ratio of 22 (calculated: 1 - 22^(-0.286))1 | The ideal gas-turbine efficiency depends only on pressure ratio; real compressors, turbines and cooling flows cut it. | A 1,600 C, 22:1 machine gives about 41.4%; best ratings are about 42-44%. |
| Turbine inlet temperature (materials) | about 1,650 C today; 1,710 C quoted for one 60 Hz model189 | Superalloys, single-crystal casting, thermal barrier coatings and ceramic matrix composites set how hot the gas can be. Rhenium is added to some nickel superalloys for strength above 1,000 C. | Ceramic matrix composites run at about 1,200-1,300 C (2,200-2,400 F) and the next combined-cycle goal is 70% net. |
| Jet engine overall efficiency | ideal thermal limit somewhat above 80%; practical 65-70% thermal; propulsive up to 90-95%8 | Safety, weight and cost cap what can be built. | About 40% overall, up from about 10% in the late 1940s; a further gain of roughly 7% per decade is judged possible with enough investment. |
Sources
- Gas Turbines: Past, Present and Future (Efficiency Focus), S.C. Gulen, UTSR Project Review Meeting US DOE National Energy Technology Laboratory, 2021
- GE HA Turbine Snags Another World Record for CCGT Efficiency POWER Magazine, 2018
- Electric Power Annual, Table 8.1: Average Operating Heat Rate for Selected Energy Sources, 2015 through 2025 US Energy Information Administration, 2026
- Commercial Aircraft Propulsion and Energy Systems Research, Chapter 3: Aircraft Gas Turbine Engines National Academies of Sciences, Engineering, and Medicine, 2016
- Mineral Commodity Summaries 2026: Rhenium US Geological Survey, 2026
- Air-cooled generators (GEN-A) GE Vernova, 2025
- GTCC business summary 2025 (investor presentation; market data from McCoy Power Reports) Mitsubishi Heavy Industries, 2025
- M501J series gas turbine specifications Mitsubishi Power, 2026