Mechanical power transmission: Overview
What it does
The job the technology does for people, in a short paragraph
Mechanical power transmission carries the work of one engine to many machines. Mills from 1771 drove rows of spinning frames from a single water wheel through gears, shafts and belts [1]. Cities later piped power itself: London's hydraulic mains ran 180 miles at their peak [2]. Today about a third of industrial and commercial electric motors drive their loads through belts [4], and US fluid power, hydraulics and pneumatics, used 2.0 to 2.9 quads of energy in 2008 [3].
as of 2026-11-12
How it works
The working principle in plain words, step by step
There are two families. Rigid links carry power as rotation: a shaft turns, gears of different sizes trade speed for turning force, and belts or ropes carry the rotation across a room. In early mills one water wheel turned a line shaft running the length of the building, and belts took power down to each machine [1]. Fluid links carry power as pressure instead. A pump pushes water or oil into pipes; at the far end the pressure drives a ram, a lift or a motor. London's hydraulic company did this with a citywide network at a nominal 800 psi [2]. Compressed air works in the same way, but air is springy and leaks easily, so it is the least efficient: leaks can waste 20 to 30% of a compressor's output [5].
as of 2026-11-12
Key figures
The handful of numbers that size it up, each with its unit, year and source
| Figure | Value | Unit | Year | Source |
|---|---|---|---|---|
| Energy used by US fluid power systems, upper end of 2.0 to 2.9 | 2.9 | quads per year | 2008 | [3] |
| Average efficiency of US fluid power systems | 22 | % | 2008 | [3] |
| Efficiency of synchronous (toothed) belt drives | 98 | % | 2012 | [4] |
| Share of a compressor's output that leaks can waste, upper end | 30 | % | 2026 | [5] |
| Length of London's hydraulic power mains at their peak | 180 | miles | – | [2] |
as of 2026-11-12. The ORNL figures are for 2008 [3]; the 22% is the study's weighted average across all segments, built on the same 2008-based estimates. The belt and leak figures are engineering rules of thumb, dated by their tip sheet (2012) and fact sheet (2026) [4][5]. The Science Museum gives no year for London's peak network [2].
Where it is used
The main places and products the technology is found in
- Belt drives on fans, pumps and machines, used by about a third of industrial and commercial electric motors [4]
- Industrial and mobile hydraulics, from presses to off-road machines [3]
- Factory compressed-air systems [5]
- Historic city hydraulic networks powering lifts, cranes, theatre machinery and the backup mechanism of Tower Bridge [2]
as of 2026-11-12
Scale today
How much of it there is now: units in use, made each year and who uses it
- Installed
- About one third of industrial and commercial electric motors use belt drives [4]
- Users
- US fluid power used 2.0 to 2.9 quads in 2008, emitting 310 to 380 million tonnes of CO2 [3]
- Unit
- quads per year
- Year
- 2008
- Note
- Industrial hydraulics used about 1.1 quads, mobile hydraulics 0.4 to 1.3 and pneumatics about 0.5 quads a year [3]. No world total was found.
as of 2026-11-12
Sources
- History & Development Derwent Valley Mills World Heritage Site
- London Hydraulic Power Company Science Museum Group Collection, 2025
- Estimating the Impact (Energy, Emissions and Economics) of the U.S. Fluid Power Industry (ORNL/TM-2011/14), Love, Lanke and Alles Oak Ridge National Laboratory, 2012
- Replace V-Belts with Notched or Synchronous Belt Drives US Department of Energy, Advanced Manufacturing Office (Motor Systems Tip Sheet), via NREL, 2012
- Compressed Air System Leaks (Improving Compressed Air System Performance, Fact Sheet #7, Rev. 1) Compressed Air Challenge, 2026