Material Insights · Understanding the Material World

Open-hearth steelmaking: Overview

What it does

The job the technology does for people, in a short paragraph

The open hearth turns pig iron and scrap into steel in a wide, shallow furnace. Martin made the first open-hearth steel in France in 1864 [1], and up to 1950 the process made 90% of British and US steel [2]. Oxygen converters replaced it from about 1960 [2]. A few works, such as Zaporizhstal in Ukraine, still use it [13].

as of 2026-11-12

How it works

The working principle in plain words, step by step

The furnace is a shallow basin under a low roof, charged with molten pig iron, scrap, some iron ore and limestone [1]. Fuel gas and air enter at one end, burn, and sweep over the charge. The exhaust leaves through brick-filled chambers at the far end and heats the bricks. Every so often the flow is reversed, so the incoming air and gas pass through the hot bricks and arrive preheated [3]. This lifts the flame hot enough to melt steel [1][3]. Oxygen from the air and from the ore burns the extra carbon out of the iron, and the limestone takes up impurities as a slag. A heat took 12 to 18 hours, time enough to test the metal and adjust its make-up before it was tapped [2].

as of 2026-11-12

Key figures

The handful of numbers that size it up, each with its unit, year and source

FigureValueUnitYearSource
Share of steel in Britain and the United States made in open hearths90%1950[2]
Open-hearth steel made a year in Eastern-bloc countries96million tons1988[2]
Time to produce one heat, low end of 12 to 18 hours12hours– [2]
Temperature to which air and fuel gas were preheated800°C– [2]
Steel capacity of Zaporizhstal's seven open-hearth furnaces and one twin-hearth unit4million t a year2023[13]

as of 2026-11-12. The 1950 share is the source's 'up to 1950' for Britain and the United States. The heat time and preheat temperature describe the process in its working life; the source shows no date for them [2]. The Zaporizhstal capacity is from a company profile last updated in 2023, which is the page's year, not a data year [13].

Where it is used

The main places and products the technology is found in

  • Steel rails, made at Landore in Wales by 1870 [5]
  • Plate and sections for ships, bridges and buildings, as the main steel process in Britain and the United States up to 1950 [2]
  • Steel of controlled make-up, since each slow heat could be tested and adjusted before tapping [2]
  • Eastern-bloc steelworks into the late 1980s [2]
  • A few remaining works, such as Zaporizhstal in Ukraine [13]

as of 2026-11-12

Scale today

How much of it there is now: units in use, made each year and who uses it

Installed
A few works; Zaporizhstal in Ukraine has seven open-hearth furnaces and one twin-hearth unit [13]
Made per year
Not reported separately; Zaporizhstal's open hearths have 4 million t a year of capacity [13]
Unit
t of crude steel
Year
2025
Note
World Steel in Figures puts 0.3% of the world's 1,849 million t of crude steel in 2025 under processes other than oxygen and electric furnaces, without naming them [9], so the open hearth's world share is at most that (calculated).

Indicative · as of 2026-11-12

Sources

  1. open-hearth process Encyclopaedia Britannica
  2. Bessemer steel Encyclopaedia Britannica
  3. Wikipedia: Open-hearth furnace
  4. Landore Siemens Steel Co Grace's Guide to British Industrial History
  5. World Steel in Figures 2026 World Steel Association, 2026
  6. Zaporizhstal Iron and Steel Works GMK Center, 2023