Material Insights · Understanding the Material World

Force, motion and energy: the laws every machine obeys: Work, energy and power: the engineer's first audit

All courses / Understanding Engineering / Module 3: Force, motion and energy: the laws every machine obeys Part 2 of 5

Work, energy and power: the engineer's first audit

Force tells you what a machine pushes with. Energy tells you what the push costs and where the cost goes. This part defines work, energy and power in the units an electricity bill uses, climbs a hill by bicycle to price it in joules and food, sizes a lift motor, and presents conservation of energy as a bookkeeping rule that every design must balance.

2.1 Work is force through a distance, and it turns up as motion, height or heat

In physics, work is done when a force moves something along its own direction: work = force x distance. The unit is the joule, the work of one newton over one metre. A joule is small: lifting a 1 kg bag of atta from the floor to a shelf 1 m up takes about 10 J. Energy is the stored ability to do work and has the same unit, and the two are linked: work done on a body goes into its energy.

Two stores of energy cover most machines. A moving body has kinetic energy, half x mass x speed squared. The squared speed matters: double the speed and the energy rises fourfold, which is why a vehicle at 80 km/h carries four times the energy of one at 40 km/h. A raised body has gravitational potential energy, mass x g x height. Notice that the potential energy depends on the height gained, not on the route. Water pumped to a rooftop tank gains the same height energy whether its pipe runs straight up the wall or winds round the building; the longer pipe adds friction loss, not height energy.

The third place energy goes is heat. Friction does work against motion, and that work becomes warmth in the surfaces.

A bicycle on a hill brings all three together. The rider must supply the potential energy of the height gained, plus the heat from rolling resistance and air. The worked estimate below shows that on a modest 5 per cent hill, the height term is the biggest by far.

Data Worked estimate 3: a bicycle up a hill, 1 km long and 50 m high, at 12 km/h
StepWorkingResult
Mass of rider and bicycle75 kg + 10 kg85 kg
Speed and time12 km/h = 3.33 m/s; 1,000 m / 3.33 m/s300 s
Height energy85 x 9.8 x 5041.7 kJ
Rolling resistance (coefficient 0.01)0.01 x 85 x 9.8 = 8.3 N, times 1,000 m8.3 kJ
Air drag (drag area 0.5 m2, air 1.2 kg/m3)half x 1.2 x 0.5 x 3.33 x 3.33 = 3.3 N, times 1,000 m3.3 kJ
Total work at the wheel41.7 + 8.3 + 3.353 kJ
Power at the wheel53 kJ / 300 sabout 178 W
Power at the pedals (chain 97 per cent efficient)178 / 0.97about 183 W

Check: a fit amateur can hold 150 to 250 W for an hour, and a casual rider only about 100 W. So a 5 per cent hill at 12 km/h is hard but possible, which matches experience. The height term is 78 per cent of the total.

Source: Bloomfield, How Things Work (Wiley, 2015), ch. 1, 'The Laws of Motion, Part 1'
  • Bloomfield, How Things Work (Wiley, 2015) · ch. 1, 'The Laws of Motion, Part 1'
  • Bloomfield, How Things Work (Wiley, 2015) · ch. 2, 'The Laws of Motion, Part 2'

2.2 Power is the rate of doing work, and it is what sizes motors, cables and fuel supply

Power is work done per second: power = work / time, or force x speed for steady motion. One watt is one joule per second. The old unit horsepower is about 746 W, and Indian vehicle and pump ratings often mix kilowatts and horsepower, so carry the conversion with you. A kilowatt-hour is an amount of energy, the energy of a 1 kW appliance running for one hour. A kilowatt is a rate.

Power matters because machines have limits on how fast they can convert or carry energy. A motor or cable overheats, and a rider tires, if asked for too much power. Energy decides how much fuel or food you need over a trip. Power decides how big the engine, motor or rider must be to do it in the time wanted. The same climb done in half the time needs twice the power but the same energy.

A passenger lift shows the point well. Without a counterweight, the motor would lift the car and passengers all the way up, with power = weight x speed, and then waste all that energy as heat in a brake coming down. Real traction lifts hang a counterweight on the other end of the rope, equal to the empty car plus a share of the rated load. As the car goes up, the counterweight comes down, and the motor needs to supply only the difference. For the 8-person lift in the table, the counterweight cuts the peak mechanical power from about 13 kW to about 3.4 kW.

The lift also shows that average and peak differ. A lift that is half full, going up, is almost perfectly balanced, and draws little power. The motor and drive must still be sized for the worst case: a full car climbing. Designers always ask which case sets the size.

Data Worked estimate 4: motor power for an 8-person traction lift moving at 1 m/s
StepWorkingResult
Rated load and empty car630 kg; car 700 kg1,330 kg moving up at full load
Counterweight (car + 45 per cent of rated load)700 + 0.45 x 630about 983 kg
Unbalanced mass at full load going up1,330 - 983about 347 kg
Unbalanced force347 x 9.83,400 N
Mechanical power at 1 m/s3,400 N x 1 m/s3.4 kW
Electrical power if drive and motor are 80 per cent efficient3.4 / 0.8about 4.3 kW
Same lift with no counterweight1,330 x 9.8 x 1about 13 kW
Half-full car going up (315 kg)(700 + 315) - 983 = 32 kg; 32 x 9.8 x 1about 0.3 kW

Check: one UK maker's product page gives a drive power of 2.45 kW for its conventional machine-room-less traction lift at 1.0 m/s, offered for 630 kg and 1,000 kg loads, and 1.8 kW for a slower 0.5 m/s design. The page does not say which load the 2.45 kW goes with or how it is measured. Our worst case of 3.4 kW is about 40 per cent higher, so treat this estimate as good to a factor of about 1.5, not better.

Source: Ideal Lifts, 'IL3 Eco-Drive lift' product page (UK maker, read November 2026), 630 kg or 1,000 kg rated load; drive power 1.8 kW for the 0.5 m/s Eco-Drive; 2.45 kW for the conventional machine-room-less traction comparison at 1.0 m/s; https://www.ideallifts.com/new-lifts/lift-models/il3/
  • Bloomfield, How Things Work (Wiley, 2015) · ch. 2, 'The Laws of Motion, Part 2'
  • Ideal Lifts, 'IL3 Eco-Drive lift' product page (UK maker, read November 2026) · 630 kg or 1,000 kg rated load; drive power 1.8 kW for the 0.5 m/s Eco-Drive; 2.45 kW for the conventional machine-room-less traction comparison at 1.0 m/s; https://www.ideallifts.com/new-lifts/lift-models/il3/

2.3 Conservation of energy lets you audit any machine: energy is moved and turned into heat, never made

The law of conservation of energy says that, in any closed system, the total of all forms of energy stays the same. Energy changes form: chemical to motion, motion to height, height to heat. It is not created and it is not destroyed. For an engineer this is less a deep thought than a working check. If energy goes into a device and the outputs do not add up to it, something is missing, and the missing item is found by looking for heat.

The audit has a routine that you can use on any device. First draw a boundary around it. Second, list the energy crossing the boundary in: fuel, electricity, food. Third, list the useful energy out: motion, height, light. Fourth, list the heat and other losses. Fifth, check that the lists balance, and if they do not, look for an unnoticed path. This habit catches impossible claims quickly. A machine claiming to give out more useful energy than it takes in, a perpetual motion machine, fails the audit without anyone needing to find the fault in its gears.

The cyclist is a good device to audit because the chain is short. The hill needs about 53 kJ at the wheel, and with chain and muscle losses the rider's body consumes about 220 kJ of food energy, about 52 kcal. Roughly three quarters of the food energy leaves the rider as heat, which is why you sweat on a climb. The flow figure sets out the chain.

Heat is never destroyed either, but it is hard to use again. Why heat is a low-grade form of energy is the subject of module 6 on heat and thermodynamics. For now, treat 'lost' as meaning 'spread out as warmth we cannot easily collect'.

Process flowchart One energy chain: food to hill for a cyclist climbing 50 m in 5 minutes
Inputs Food energyabout 220 kJ (52 kcal) Process steps 1 Muscles

chemical to mechanical work, about 25 per cent efficient; about 165 kJ leaves the body as heat

2 Pedals and chain

about 97 per cent efficient; about 2 kJ lost as heat in the chain

3 Wheel on the road

53 kJ of work done against gravity, rolling and air

Outputs Height gainedabout 42 kJ, stored as potential energy Rolling resistanceabout 8 kJ as warmth in tyre and road Air dragabout 3 kJ as warmth in the air

The outputs plus the heat from muscles and chain add up to the 220 kJ eaten: 42 + 8 + 3 + 165 + 2.

Source: Bloomfield, How Things Work (Wiley, 2015), ch. 1, 'The Laws of Motion, Part 1'
  • Bloomfield, How Things Work (Wiley, 2015) · ch. 1, 'The Laws of Motion, Part 1'
  • Bloomfield, How Things Work (Wiley, 2015) · ch. 2, 'The Laws of Motion, Part 2'

See it in the table

H₂O WaterEl Electricity

Check your understanding

A rider and bicycle of 85 kg climb a 50 m hill. Ignoring all drag, the energy needed is about:

Energy gained in height = m x g x h = 85 x 9.8 x 50, about 41,650 J, roughly 42 kJ. The answer does not depend on how steep the road is or how fast the rider goes.

A lift has a counterweight equal to the empty car plus 45 per cent of the rated load. Why is that chosen?

The counterweight stores energy as the car descends and gives it back as the car rises. The motor then handles only the difference, so a typical lift needs a modest motor and little electricity.

A cyclist's muscles are about 25 per cent efficient. A climb needs 55 kJ at the pedals. About how much food energy does it use?

Food energy = 55 / 0.25 = 220 kJ. The other 165 kJ leaves the body as heat, which is why a climber warms up.
← Part 1: Force, weight and friction: what pushes a machine and what holds it backMark read · Part 3: Momentum, collisions and stopping: how safety design works →