Material Insights · Understanding the Material World

Steel reinforcing bar: Footprint

Raw materials in one unit

Every commodity and chemical inside one unit, traced through its components by the site, with its emission factor and emissions

VariantMaterialAmount (kg)Emission factor (kg CO2e per kg)Emissions (kg CO2e)
BlastIron ore1452– –
BlastCoking coal830– –
BlastCrushed stone311– –
BlastSteel1241.92238.1
ScrapSteel9131.921753
ScrapCrushed stone66.4– –
ScrapCoking coal16.6– –

Worked out from data

The site's estimate

Emissions of one unit worked out by the site from its materials and energy, for the world and India, with the share of mass covered by emission factors

VariantStagePlaceEmissions (kg CO2e)Mass covered by factors
BlastMakingWorld20855%
BlastUseWorld– –
BlastMakingIndia21225%
BlastUseIndia– –
ScrapMakingWorld175392%
ScrapUseWorld– –
ScrapMakingIndia175392%
ScrapUseIndia– –
DRIMakingWorld1543–
DRIUseWorld– –
DRIMakingIndia1701–
DRIUseIndia– –

Worked out from data

Energy to make it

Energy used to make one unit, by carrier and stage

Energy to make 4
  • Ht Heat 25,200 MJ · Manufacturing Blast furnace Specific energy consumption of Indian BF-BOF TMT rebar, 25.20 GJ per tonne, all carriers (RMI Exhibit 14, 2024 values); converted to MJ (calculated) [7]. Tata Steel's EPD gives 26,500 MJ of non-renewable primary energy (energy carriers) cradle to gate [6]
  • El Electricity 174 kWh · Manufacturing Blast furnace Oxygen furnace route electricity per tonne of steel, already within the 25.20 GJ [7]
  • Ht Heat 17,130 MJ · Manufacturing DRI electric furnace Coal-based DRI-EAF/IF TMT, 17.13 GJ per tonne in 2024, all carriers (calculated conversion) [7]; gas-based DRI is 9.91 GJ [7]
  • El Electricity 745 kWh · Manufacturing DRI electric furnace Midpoint of 664 to 825 kWh per tonne of steel for electric furnace routes (calculated) [7]

Indicative · as of 2026-11-16. Heat rows are total specific energy including the electricity row, so the two rows overlap. Energy for scrap-only arc furnaces was not found in an opened source.

Emissions by stage

Published life-cycle emissions of one unit in four stages (making, logistics, use, end of life), with their split, place and variant

StageValueRangeUnitVariantPlaceYearSource
Making2730– kg CO2e per tonne of rebar (A1 to A3, Tata Steel EPD: A1 2,520, A2 2.16, A3 205)Blast furnaceIndia2021[6]
Making28502700 to 3000 kg CO2e per tonne of TMT rebar (RMI range of 2.7 to 3.0 t; midpoint calculated)kg CO2e per tonne of TMT rebar (RMI range of 2.7 to 3.0 t; midpoint calculated)Blast furnaceIndia2025[7]
Making652– kg CO2e per tonne of fabricated rebar (A1 to A3, CMC Sayreville EPD: A1 613, A2 23.6, A3 15.3)Scrap electric arcUnited States of America2014[4]
Making854– kg CO2e per tonne of fabricated rebar (A1 to A3, CRSI industry EPD: A1 778, A2 49, A3 27)Scrap electric arcUnited States of America2020[3]
Making1930– kg CO2e per tonne of rebar (A1 to A3, Ezz Steel EPD: A1 1,050, A2 127, A3 757)DRI electric furnaceEgypt2024[5]
Making19001800 to 2000 kg CO2e per tonne of TMT rebar, electric furnace routes (RMI range 1.8 to 2.0 t; midpoint calculated)kg CO2e per tonne of TMT rebar, electric furnace routes (RMI range 1.8 to 2.0 t; midpoint calculated)DRI electric furnaceIndia2025[7]
Making2320– kg CO2 per tonne of crude steel, world average (not rebar; cross-check)Blast furnaceWorld2023[1]
Making1430– kg CO2 per tonne of crude steel, world average (not rebar; cross-check)DRI electric furnaceWorld2023[1]
Making700– kg CO2 per tonne of crude steel, world average (not rebar; cross-check)Scrap electric arcWorld2023[1]
Logistics2.16– kg CO2e per tonne (module A2: inbound transport of raw materials only; delivery to site not included)Blast furnaceIndia2021[6]
Logistics23.6– kg CO2e per tonne (module A2: inbound transport only)Scrap electric arcUnited States of America2014[4]
Logistics127– kg CO2e per tonne (module A2: inbound transport only)DRI electric furnaceEgypt2024[5]

as of 2026-11-16. Making figures are EPD cradle-to-gate results for different years and countries, so the gap between routes mixes route and grid. No opened source gives use-stage emissions (a buried bar uses no energy) or end-of-life emissions per tonne, so those stages are left out.

End of life

What happens to a unit when it is thrown away: collection, reuse, recycling and disposal shares, by place

RouteSharePlaceYearSource
Recycling credit applied over 85% of the steel in Tata Steel's rebar EPD85India2022[6]
Global steel recycling rate, low end of 'around 80 to 90%'80World2020[15]
Global steel recycling rate, high end of 'around 80 to 90%'90World2020[15]

as of 2026-11-16

Recovered as

The commodities and chemicals recovered at end of life, with recovery rates

Recovered as
  • St Steel 85% recovered · Recycling: melted again in an electric furnace Tata Steel's EPD assumes 85% of the steel is recycled at end of life and counts 850 kg per tonne as material for recycling [6]. Each tonne of scrap used saves about 1.1 t of iron ore, 630 kg of coking coal and 55 kg of limestone [7]

as of 2026-11-16

End of life in India

Collection and recycling in India, including the informal sector

Rebar leaves service when a building is demolished, after 30 to 50 years for steel products in India [7]. It is recovered as scrap and is readily recycled [16, 1]. India's domestic scrap generation was about 25 Mt in FY24, with 9 Mt imported, and the informal workforce handles over 50% of urban scrap recovery [7]. No opened source gives a recovery rate for rebar alone.

as of 2026-11-16

Water and waste

Water use and waste per unit where a source gives them

MeasureValueUnitStageYearSource
Net fresh water use, blast furnace route (A1 2.80 + A2 0.0074 + A3 0.739 m3, calculated)3.55m3 per tonneMaking2021[6]
Net fresh water use, scrap electric arc (CMC Sayreville)2.79m3 per tonneMaking2014[4]
Net fresh water use, scrap electric arc (CRSI industry EPD)8.42m3 per tonneMaking2020[3]

as of 2026-11-16

Sources

  1. World Steel in Figures 2025 World Steel Association, 2025
  2. Environmental Product Declaration: fabricated steel reinforcing bar (CRSI industry-wide EPD) Concrete Reinforcing Steel Institute; ASTM International programme operator, 2022
  3. Environmental Product Declaration of Fabricated Concrete Reinforcing Steel, CMC Sayreville (SCS-EPD-05357) SCS Global Services, for Commercial Metals Company, 2016
  4. EPD 0038: carbon steel reinforcing bars, DRI route (Ezz Steel) CARES, 2025
  5. EPD S-P-05018: Steel Rebar, Tata Steel Limited International EPD System, 2022
  6. The Rebar Opportunity: Decarbonising the Backbone of India's Built Environment RMI India Foundation with BMTPC and Lodha Foundation, 2025
  7. Iron and Steel Technology Roadmap International Energy Agency, 2020
  8. Green Attributes of Rebar Concrete Reinforcing Steel Institute