Material Insights · Understanding the Material World

Fracture mechanics: Technologies

Technologies

The technologies that rely on it, and how each one uses it

Relied on by 5
  • St Knapped stone tools A blow starts a crack that runs through brittle stone along a predictable path, and controlling that crack is the craft of knapping.
  • CFR Carbon fibre composites A crack in the resin is stopped or turned aside where it meets strong fibres, so the composite resists the spread of damage.
  • UOG Unconventional oil and gas Hydraulic fracturing pumps fluid into rock until the energy pushing the crack open exceeds the rock's resistance, so the crack grows and lets gas or oil flow.
  • Vst Soft body armour In principle terms, it relies on fibres that are very tough, so they absorb a projectile's energy by stretching and breaking across many strands instead of letting a crack run through.
  • AGS Advanced geothermal Enhanced systems open cracks in tight rock with water pressure, as tested at Fenton Hill.
Limits 24
  • Arc Masonry arch Stone and mortar crack easily when pulled, so an arch must be shaped to stay in compression; where any part is put in tension, a crack opens.
  • Apl Powered fixed-wing aeroplane Fatigue cracks growing from holes near the cabin windows broke up Comet airliners, and airframes are now designed and inspected so that cracks are found before they reach a critical size [7].
  • Vst Soft body armour Griffith's 1920 work showed that small flaws control when a solid breaks, which caps the strength of any fibre.
  • CFR Carbon fibre composites The fibres are strong along their length, but cracks between layers and hidden impact damage set how far a composite part can be loaded.
  • WC Cemented carbide Carbide grains are brittle ceramics, so the material's toughness, its resistance to cracks, sets how hard a tool can be pushed; Griffith's 1921 theory explains strength through the flaws a material holds.
  • 3DC 3D-printed construction Unreinforced printed concrete cracks easily under tension, and the joins between layers are weak planes, so reinforcement remains a key problem.
  • IFB Iron-framed building Cast iron is brittle and weak in tension, so a beam can crack suddenly under a pull; this limited spans and loads.
  • IHS Iron and steel ship hull Welded Liberty ships cracked from square hatch corners in cold seas, showing that hull steel must resist the spread of cracks.
  • Aeroplane Repeated flight loads grow cracks in a metal or composite structure, which sets inspection and design rules.
  • Aircraft engine Life-limited parts such as discs and shafts carry a cycle limit and are replaced at fixed intervals.
Show 14 more
  • Bicycle Frames, forks and cranks must resist cracks that grow under repeated loads.
  • Carbon fibre and composite parts Cracks between layers and hidden impact damage limit how far a part can be loaded.
  • Flat glass sheet Glass is brittle: flaws on its surface set how much load a pane carries before it breaks.
  • Glass container Glass is brittle, and a source describes a physical boundary to lighter bottles set by its fragility.
  • Precast concrete products Plain concrete cracks under tension, which is why steel or prestress is added.
  • Rolling bearing Repeated rolling stress starts cracks below the surface and causes flaking, which sets the bearing's fatigue life.
  • Vehicle transmission Gear teeth must survive millions of load cycles without cracking at the root.
  • Wind turbine blade Cracks in the laminate and in the bond lines grow under millions of load cycles, which sets the design life.
  • Wind turbine tower Weld seams and flange bolts see millions of load cycles, so crack growth limits the life of a tower.
  • Dme Large masonry dome Masonry hardly resists pulling, so the spreading base of a dome cracks; iron rings were fitted to St Peter's dome by 1748 to hold it.
  • PSC Prestressed concrete Concrete cracks under small tensile stress; prestressing exists to keep it out of tension.
  • Rly Railway (iron track network) Repeated wheel loads grow fatigue cracks, such as the gauge corner cracking in rail recovered after the Hatfield crash of 2000, so rails must be inspected and replaced before a crack reaches a critical size.
  • RCo Reinforced concrete Concrete cracks under small tensile stress, which is why it needs steel at all and why crack widths are checked.
  • Sky Steel-frame skyscraper Welded steel joints must resist cracks, and fatigue from wind and repeated loads limits how they are designed.

as of 2026-11-10

Sources

  1. Introduction to Fracture Mechanics David Roylance, Department of Materials Science and Engineering, MIT (MIT OpenCourseWare, 3.11 Mechanics of Materials), 2001